C8051F067-GQ Silicon Laboratories Inc, C8051F067-GQ Datasheet - Page 296

• Manufacturer Part Number: C8051F067-GQ
• Description: IC 8051 MCU 32K FLASH 64TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F06xr

Specifications of C8051F067-GQ

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 24
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 4.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 2x16b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: C8051F0x
• Core: 8051
• Data Bus Width: 8 bit
• Data Ram Size: 4.25 KB
• Interface Type: I2C, SMBus, SPI, UART
• Maximum Clock Frequency: 25 MHz
• Number Of Programmable I/os: 24
• Number Of Timers: 5
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Development Tools By Supplier: C8051F060DK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit, 1 Channel
• On-chip Dac: 12 bit, 2 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 336-1222

C8051F060/1/2/3/4/5/6/7
24.2.2. Capture Mode
In Capture Mode, Timer 2, 3, and 4 will operate as a 16-bit counter/timer with capture facility. When the
Timer External Enable bit (found in the TMRnCN register) is set to ‘1’, a high-to-low transition on the TnEX
input pin causes the 16-bit value in the associated timer (THn, TLn) to be loaded into the capture registers
(RCAPnH, RCAPnL). If a capture is triggered in the counter/timer, the Timer External Flag (TMRnCN.6)
will be set to ‘1’ and an interrupt will occur if the interrupt is enabled. See
on page 151
As the 16-bit timer register increments and overflows TMRnH:TMRnL, the TFn Timer Overflow/Underflow
Flag (TMRnCN.7) is set to ‘1’ and an interrupt will occur if the interrupt is enabled. The timer can be config-
ured to count down by setting the Decrement Enable Bit (TMRnCF.0) to ‘1’. This will cause the timer to
decrement with every timer clock/count event and underflow when the timer transitions from 0x0000 to
0xFFFF. Just as in overflows, the Overflow/Underflow Flag (TFn) will be set to ‘1’, and an interrupt will
occur if enabled.
Counter/Timer with Capture mode is selected by setting the Capture/Reload Select bit CP/RLn
(TMRnCN.0) and the Timer 2, 3, and 4 Run Control bit TRn (TnCON.2) to logic 1. The Timer 2, 3, and 4
respective External Enable EXENn (TnCON.3) must also be set to logic 1 to enable a captures. If EXENn
is cleared, transitions on TnEX will be ignored.
296
External Clock
SYSCLK
(XTAL1)
Tn
TnEX
for further information concerning the configuration of interrupt sources.
Crossbar
8
2
12
Crossbar
EXENn
Figure 24.11. T2, 3, and 4 Capture Mode Block Diagram
TRn
0
1
TMRnCF
Capture
M
T
n
1
M
T
n
0
T
O
G
n
O
E
T
n
Rev. 1.2
TCLK
D
C
N
E
RCAPnL
TMRnL
0xFF
RCAPnH
TMRnH
0xFF
OVF
Toggle Logic
Section “13.3. Interrupt Handler”
CP/RLn
EXENn
EXFn
C/Tn
TRn
TFn
0
1
Interrupt
(Port Pin)
Tn