ATMEGA8L-8AC Atmel, ATMEGA8L-8AC Datasheet - Page 46

• Manufacturer Part Number: ATMEGA8L-8AC
• Description: IC AVR MCU 8K LV 8MHZ COM 32TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA8L-8AC

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 23
• Program Memory Size: 8KB (4K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 32-TQFP, 32-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: ATMEGA8L8AC

Interrupts
Interrupt Vectors
in ATmega8
46
ATmega8(L)
This section describes the specifics of the interrupt handling performed by the ATmega8. For a
general explanation of the AVR interrupt handling, refer to
page
Table 18. Reset and Interrupt Vectors
Notes:
Table 19 on page 47
of BOOTRST and IVSEL settings. If the program never enables an interrupt source, the Interrupt
Vectors are not used, and regular program code can be placed at these locations. This is also
the case if the Reset Vector is in the Application section while the Interrupt Vectors are in the
boot section or vice versa.
Vector No.
10
11
12
13
14
15
16
17
18
19
14.
1
2
3
4
5
6
7
8
9
1. When the BOOTRST Fuse is programmed, the device will jump to the Boot Loader address at
2. When the IVSEL bit in GICR is set, Interrupt Vectors will be moved to the start of the boot
reset, see
Flash section. The address of each Interrupt Vector will then be the address in this table added
to the start address of the boot Flash section
Address
Program
0x000
0x00A
0x00B
0x00C
0x00D
0x00E
0x001
0x002
0x003
0x004
0x005
0x006
0x007
0x008
0x009
0x00F
0x010
0x011
0x012
“Boot Loader Support – Read-While-Write Self-Programming” on page 202
(1)
shows reset and Interrupt Vectors placement for the various combinations
(2)
Source
RESET
INT0
INT1
TIMER2 COMP
TIMER2 OVF
TIMER1 CAPT
TIMER1 COMPA
TIMER1 COMPB
TIMER1 OVF
TIMER0 OVF
SPI, STC
USART, RXC
USART, UDRE
USART, TXC
ADC
EE_RDY
ANA_COMP
TWI
SPM_RDY
Interrupt Definition
External Pin, Power-on Reset, Brown-out
Reset, and Watchdog Reset
External Interrupt Request 0
External Interrupt Request 1
Timer/Counter2 Compare Match
Timer/Counter2 Overflow
Timer/Counter1 Capture Event
Timer/Counter1 Compare Match A
Timer/Counter1 Compare Match B
Timer/Counter1 Overflow
Timer/Counter0 Overflow
Serial Transfer Complete
USART, Rx Complete
USART Data Register Empty
USART, Tx Complete
ADC Conversion Complete
EEPROM Ready
Analog Comparator
Two-wire Serial Interface
Store Program Memory Ready
“Reset and Interrupt Handling” on
2486Z–AVR–02/11