PIC16C770/JW Microchip Technology, PIC16C770/JW Datasheet - Page 71

• Manufacturer Part Number: PIC16C770/JW
• Description: IC MCU EPROM2KX14 A/D PWM 20CDIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Cr

Specifications of PIC16C770/JW

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SPI
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 15
• Program Memory Size: 3.5KB (2K x 14)
• Program Memory Type: EPROM, UV
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 6x12b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 20-CDIP (0.300", 7.62mm) Window
• For Use With: DVA16XP200 - ADAPTER ICE 20DIP/SOIC/SSOPAC164028 - MODULE SKT PROMATEII 20SOIC/DIP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

REGISTER 9-3:
2002 Microchip Technology Inc.
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
SYNC SERIAL PORT CONTROL REGISTER2 (SSPCON2: 91h)
GCEN: General Call Enable bit (In I
1 = Enable interrupt when a general call address (0000h) is received in the SSPSR.
0 = General call address disabled.
ACKSTAT: Acknowledge Status bit (In I
In Master Transmit mode:
1 = Acknowledge was not received from slave
0 = Acknowledge was received from slave
ACKDT: Acknowledge Data bit (In I
In Master Receive mode:
Value that will be transmitted when the user initiates an Acknowledge sequence at the end of
1 = Not Acknowledge (NACK)
0 = Acknowledge (ACK)
ACKEN: Acknowledge Sequence Enable bit (In I
In Master Receive mode:
1 = Initiate Acknowledge sequence on SDA and SCL pins, and transmit ACKDT data bit.
0 = Acknowledge sequence IDLE
RCEN: Receive Enable bit (In I
1 = Enables Receive mode for I
0 = Receive IDLE
PEN: STOP Condition Enable bit (In I
SCK Release Control
1 = Initiate STOP condition on SDA and SCL pins. Automatically cleared by hardware.
0 = STOP condition IDLE
RSEN: Repeated START Condition Enabled bit (In I
1 = Initiate Repeated START condition on SDA and SCL pins. Automatically cleared by
0 = Repeated START condition IDLE
SEN: START Condition Enabled bit (In I
1 = Initiate START condition on SDA and SCL pins. Automatically cleared by hardware.
0 = START condition IDLE
bit 7
Legend:
R = Readable bit
- n = Value at POR
Note:
R/W-0
GCEN
a receive.
Automatically cleared by hardware.
hardware.
For bits ACKEN, RCEN, PEN, RSEN, SEN: If the I
mode, this bit may not be set (no spooling) and the SSPBUF may not be written (or
writes to the SSPBUF are disabled).
ACKSTAT
R/W-0
Advance Information
ACKDT
R/W-0
W = Writable bit
’1’ = Bit is set
2
2
C Master mode only).
C
2
2
C Master mode only)
C Slave mode only)
ACKEN
2
R/W-0
C Master mode only).
2
2
C Master mode only)
C Master mode only)
PIC16C717/770/771
2
R/W-0
RCEN
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared
C Master mode only).
2
C Master mode only)
R/W-0
PEN
2
C module is not in the IDLE
x = Bit is unknown
R/W-0
RSEN
DS41120B-page 69
R/W-0
SEN
bit 0