C8051F122 Silicon Laboratories Inc, C8051F122 Datasheet - Page 192

• Manufacturer Part Number: C8051F122
• Description: IC 8051 MCU FLASH 128K 100TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F12xr

Specifications of C8051F122

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 100MHz
• Connectivity: EBI/EMI, SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 64
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 8.25K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 8x8b, 8x10b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Eeprom Size: -

C8051F120/1/2/3/4/5/6/7
C8051F130/1/2/3
14.7.3. Powering on and Initializing the PLL
To set up and use the PLL as the system clock after power-up of the device, the following procedure
should be implemented:
If the PLL characteristics need to be changed when the PLL is already running, the following procedure
should be implemented:
192
Step 1. Ensure that the reference clock to be used (internal or external) is running and stable.
Step 2. Set the PLLSRC bit (PLL0CN.2) to select the desired clock source for the PLL.
Step 3. Program the Flash read timing bits, FLRT (FLSCL.5–4) to the appropriate value for the
Step 4. Enable power to the PLL by setting PLLPWR (PLL0CN.0) to ‘1’.
Step 5. Program the PLL0DIV register to produce the divided reference frequency to the PLL.
Step 6. Program the PLLLP3–0 bits (PLL0FLT.3–0) to the appropriate range for the divided
Step 7. Program the PLLICO1–0 bits (PLL0FLT.5–4) to the appropriate range for the PLL output
Step 8. Program the PLL0MUL register to the desired clock multiplication factor.
Step 9. Wait at least 5 µs, to provide a fast frequency lock.
Step 10. Enable the PLL by setting PLLEN (PLL0CN.1) to ‘1’.
Step 11. Poll PLLLCK (PLL0CN.4) until it changes from ‘0’ to ‘1’.
Step 12. Switch the System Clock source to the PLL using the CLKSEL register.
Step 1. The system clock should first be switched to either the internal oscillator or an external
Step 2. Ensure that the reference clock to be used for the new PLL setting (internal or external) is
Step 3. Set the PLLSRC bit (PLL0CN.2) to select the new clock source for the PLL.
Step 4. If moving to a faster frequency, program the Flash read timing bits, FLRT (FLSCL.5–4) to
Step 5. Disable the PLL by setting PLLEN (PLL0CN.1) to ‘0’.
Step 6. Program the PLL0DIV register to produce the divided reference frequency to the PLL.
Step 7. Program the PLLLP3–0 bits (PLL0FLT.3–0) to the appropriate range for the divided
Step 8. Program the PLLICO1-0 bits (PLL0FLT.5–4) to the appropriate range for the PLL output
Step 9. Program the PLL0MUL register to the desired clock multiplication factor.
Step 10. Enable the PLL by setting PLLEN (PLL0CN.1) to ‘1’.
Step 11. Poll PLLLCK (PLL0CN.4) until it changes from ‘0’ to ‘1’.
Step 12. Switch the System Clock source to the PLL using the CLKSEL register.
Step 13. If moving to a slower frequency, program the Flash read timing bits, FLRT (FLSCL.5–4)
clock source that is running and stable, using the CLKSEL register.
new clock rate (see
reference frequency.
frequency.
running and stable.
the appropriate value for the new clock rate (see
page 199
reference frequency.
frequency.
to the appropriate value for the new clock rate (see
).
PLL Frequency
Section “15. Flash Memory” on page 199
=
Reference Frequency
Rev. 1.4
Section “15. Flash Memory” on

Section “15. Flash Memory” on
-------------- -
PLLM
PLLN
).