MCP1725-5002E/SN Microchip Technology, MCP1725-5002E/SN Datasheet - Page 7

• Manufacturer Part Number: MCP1725-5002E/SN
• Description: IC LDO REG 500MA 5.0V 8SOIC
• Manufacturer: Microchip Technology

Specifications of MCP1725-5002E/SN

• Regulator Topology: Positive Fixed
• Voltage - Output: 5V
• Voltage - Input: Up to 6V
• Voltage - Dropout (typical): 0.21V @ 500mA
• Number Of Regulators: 1
• Current - Output: 500mA (Min)
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Primary Input Voltage: 5.35V
• Output Voltage: 5V
• Dropout Voltage Vdo: 210mV
• No. Of Pins: 8
• Output Current: 500mA
• Voltage Regulator Case Style: SOIC
• Operating Temperature Range: -40°C To +125°C
• Number Of Outputs: 1
• Polarity: Positive
• Input Voltage Max: 6 V
• Output Type: Fixed
• Dropout Voltage (max): 0.35 V at 500 mA
• Line Regulation: 0.05 % / V
• Load Regulation: 0.5 %
• Voltage Regulation Accuracy: 2 %
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Output Voltage Fixed: 5V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Limit (min): -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

AC/DC CHARACTERISTICS (CONTINUED)
TEMPERATURE SPECIFICATIONS
© 2007 Microchip Technology Inc.
Electrical Specifications: Unless otherwise noted, V
I
Boldface type applies for junction temperatures, T
AC Performance
Output Delay From SHDN
Output Noise
Power Supply Ripple Rejection
Ratio
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
Note 1:
Electrical Specifications: Unless otherwise indicated, all limits apply for V
Temperature Ranges
Operating Junction Temperature Range
Maximum Junction Temperature
Storage Temperature Range
Thermal Package Resistances
Thermal Resistance, 8LD 2x3 DFN
Thermal Resistance, 8LD SOIC
OUT
= 1 mA, C
2:
3:
4:
5:
6:
7:
Parameters
The minimum V
V
voltage for the adjustable cases. V
TCV
temperature range. V
Load regulation is measured at a constant junction temperature using low duty-cycle pulse testing. Load regulation is
tested over a load range from 1 mA to the maximum specified output current.
Dropout voltage is defined as the input-to-output voltage differential at which the output voltage drops 2% below its
nominal value that was measured with an input voltage of V
The maximum allowable power dissipation is a function of ambient temperature, the maximum allowable junction
temperature and the thermal resistance from junction to air. (i.e., T
dissipation will cause the device operating junction temperature to exceed the maximum +150°C rating. Sustained
junction temperatures above +150°C can impact device reliability.
The junction temperature is approximated by soaking the device under test at an ambient temperature equal to the
desired junction temperature. The test time is small enough such that the rise in the junction temperature over the
ambient temperature is not significant.
R
IN
is the nominal regulator output voltage for the fixed cases. V
OUT
Parameters
= C
OUT
= (V
OUT-HIGH
= 4.7 µF (X7R Ceramic), T
IN
must meet two conditions: V
OUT-LOW
– V
OUT-LOW
PSRR
ΔT
Sym
T
T
e
OR
SD
is the lowest voltage measured over the temperature range.
N
SD
R
) *10
= V
J
Sym
6
θ
θ
θ
θ
(Note 7) of -40°C to +125°C
ADJ *
A
T
T
T
/ (V
JA
JC
JA
JC
IN
A
= +25°C.
J
J
= V
Min
R
((R
—
—
—
—
—
* ΔTemperature). V
IN
OUT(MAX)
1
≥ 2.3V and V
/R
Min
-40
-65
2
—
—
—
—
—
)+1).
Typ
100
150
+ V
2.0
60
10
Figure
OUT
DROPOUT(MAX)
38.8
Typ
163
IN
76
26
—
—
—
R
= V
4-1.
≥ V
= 1.2V, 1.8V, etc. V
OUT-HIGH
A
, T
R
OUT(MAX)
Max
J
—
—
—
—
—
+ V
, θ
+125
+150
+150
Max
IN
JA
—
—
—
—
DROPOUT(MAX)
). Exceeding the maximum allowable power
= 2.3V to 6.0V.
(Note 1), V
is the highest voltage measured over the
+ V
µV/√Hz
Units
dB
µs
°C
°C
DROPOUT(MAX).
Units
°C/W
°C/W
°C/W
°C/W
°C
°C
°C
R
R
is the desired set point output
.
= 1.8V for Adjustable Output,
SHDN = GND to V
V
I
C
V
f = 100 Hz, C
I
V
C
I
V
I
V
OUT
OUT
OUT
OUT
OUT
OUT
INAC
IN
IN
OUT
IN
MCP1725
Steady State
Transient
4-Layer JC51-7
Standard Board with
vias
4-Layer JC51-7
Standard Board
= 0 µF
= 2.8V
= 2.8V
= 200 mA, f = 1 kHz,
= 10 mA,
= 100 µA, V
= 100 µA, V
= GND to 95% V
= 10 µF (X7R Ceramic),
= 2.5V
= 30 mV pk-pk,
Conditions
Conditions
DS22026B-page 7
OUT
OUT
OUT
= 10 µF,
IN
= 1.8V,
= 1.8V,
R