LT1764ET-2.5#06PBF Linear Technology, LT1764ET-2.5#06PBF Datasheet - Page 12

• Manufacturer Part Number: LT1764ET-2.5#06PBF
• Description: IC REG LDO 2.5V 3A TO220-5
• Manufacturer: Linear Technology

Specifications of LT1764ET-2.5#06PBF

• Regulator Topology: Positive Fixed
• Voltage - Output: 2.5V
• Voltage - Input: Up to 20V
• Voltage - Dropout (typical): 0.34V @ 3A
• Number Of Regulators: 1
• Current - Output: 3A
• Current - Limit (min): 3.1A
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Through Hole
• Package / Case: TO-220-5 (Bent and Staggered Leads)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

APPLICATIO S I FOR ATIO
LT1764 Series
Voltage and temperature coefficients are not the only
sources of problems. Some ceramic capacitors have a
piezoelectric response. A piezoelectric device generates
voltage across its terminals due to mechanical stress,
similar to the way a piezoelectric accelerometer or micro-
phone works. For a ceramic capacitor the stress can be
induced by vibrations in the system or thermal transients.
Overload Recovery
Like many IC power regulators, the LT1764-X has safe
operating area protection. The safe area protection de-
creases the current limit as input-to-output voltage in-
creases and keeps the power transistor inside a safe
operating region for all values of input-to-output voltage.
12
Figure 4. Ceramic Capacitor Temperature Characteristics
Figure 3. Ceramic Capacitor DC Bias Characteristics
–100
–100
–20
–40
–60
–80
–20
–40
–60
–80
20
40
20
0
0
–50
0
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
–25
2
U
4
DC BIAS VOLTAGE (V)
0
TEMPERATURE (°C)
BOTH CAPACITORS ARE 16V,
1210 CASE SIZE, 10µF
6
25
U
8
Y5V
X5R
50
10
Y5V
75
12
W
X5R
100
14
1764 F03
1764 F04
16
125
U
The protection is designed to provide some output current
at all values of input-to-output voltage up to the device
breakdown.
When power is first turned on, as the input voltage rises,
the output follows the input, allowing the regulator to start
up into very heavy loads. During the start-up, as the input
voltage is rising, the input-to-output voltage differential is
small, allowing the regulator to supply large output cur-
rents. With a high input voltage, a problem can occur
wherein removal of an output short will not allow the
output voltage to recover. Other regulators, such as the
LT1085, also exhibit this phenomenon, so it is not unique
to the LT1764 series.
The problem occurs with a heavy output load when the
input voltage is high and the output voltage is low. Com-
mon situations are immediately after the removal of a
short circuit or when the SHDN pin is pulled high after the
input voltage has already been turned on. The load line for
such a load may intersect the output current curve at two
points. If this happens, there are two stable output oper-
ating points for the regulator. With this double intersec-
tion, the input power supply may need to be cycled down
to zero and brought up again to make the output recover.
Output Voltage Noise
The LT1764 regulators have been designed to provide low
output voltage noise over the 10Hz to 100kHz bandwidth
while operating at full load. Output voltage noise is typi-
cally 50nV√Hz over this frequency bandwidth for the
LT1764 (adjustable version). For higher output voltages
(generated by using a resistor divider), the output voltage
noise will be gained up accordingly. This results in RMS
noise over the 10Hz to 100kHz bandwidth of 15µV
the LT1764 increasing to 37µV
Higher values of output voltage noise may be measured
when care is not exercised with regards to circuit layout
and testing. Crosstalk from nearby traces can induce
unwanted noise onto the output of the LT1764-X. Power
supply ripple rejection must also be considered; the LT1764
regulators do not have unlimited power supply rejection
and will pass a small portion of the input noise through to
the output.
RMS
for the LT1764-3.3.
RMS
1764fb
for