LT1764ET-2.5#06PBF Linear Technology, LT1764ET-2.5#06PBF Datasheet - Page 14

• Manufacturer Part Number: LT1764ET-2.5#06PBF
• Description: IC REG LDO 2.5V 3A TO220-5
• Manufacturer: Linear Technology

Specifications of LT1764ET-2.5#06PBF

• Regulator Topology: Positive Fixed
• Voltage - Output: 2.5V
• Voltage - Input: Up to 20V
• Voltage - Dropout (typical): 0.34V @ 3A
• Number Of Regulators: 1
• Current - Output: 3A
• Current - Limit (min): 3.1A
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Through Hole
• Package / Case: TO-220-5 (Bent and Staggered Leads)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

APPLICATIONS
LT1764 Series
Protection Features
The LT1764 regulators incorporate several protection
features which make them ideal for use in battery-powered
circuits. In addition to the normal protection features
associated with monolithic regulators, such as current
limiting and thermal limiting, the devices are protected
against reverse input voltages, reverse output voltages
and reverse voltages from output to input.
Current limit protection and thermal overload protection
are intended to protect the device against current overload
conditions at the output of the device. For normal opera-
tion, the junction temperature should not exceed 125°C.
The input of the device will withstand reverse voltages of
20V. Current flow into the device will be limited to less than
1mA and no negative voltage will appear at the output. The
device will protect both itself and the load. This provides
protection against batteries which can be plugged in
backward.
The output of the LT1764-X can be pulled below ground
without damaging the device. If the input is left open circuit
or grounded, the output can be pulled below ground by
20V. For fixed voltage versions, the output will act like a
large resistor, typically 5k or higher, limiting current flow
to typically less than 600µA. For adjustable versions, the
output will act like an open circuit; no current will flow out
of the pin. If the input is powered by a voltage source, the
output will source the short-circuit current of the device
and will protect itself by thermal limiting. In this case,
grounding the SHDN pin will turn off the device and stop
the output from sourcing the short-circuit current.
14
U
INFORMATION
U
W
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
Figure 5. Reverse Output Current
0
LT1764
LT1764-1.8
U
1
2
OUTPUT VOLTAGE (V)
3
4
5
The ADJ pin of the adjustable device can be pulled above
or below ground by as much as 7V without damaging the
device. If the input is left open circuit or grounded, the ADJ
pin will act like an open circuit when pulled below ground
and like a large resistor (typically 5k) in series with a diode
when pulled above ground.
In situations where the ADJ pin is connected to a resistor
divider that would pull the ADJ pin above its 7V clamp
voltage if the output is pulled high, the ADJ pin input
current must be limited to less than 5mA. For example, a
resistor divider is used to provide a regulated 1.5V output
from the 1.21V reference when the output is forced to 20V.
The top resistor of the resistor divider must be chosen to
limit the current into the ADJ pin to less than 5mA when the
ADJ pin is at 7V. The 13V difference between OUT and ADJ
pins divided by the 5mA maximum current into the ADJ pin
yields a minimum top resistor value of 2.6k.
In circuits where a backup battery is required, several
different input/output conditions can occur. The output
voltage may be held up while the input is either pulled to
ground, pulled to some intermediate voltage, or is left
open circuit. Current flow back into the output will follow
the curve shown in Figure 5.
When the IN pin of the LT1764-X is forced below the OUT
pin or the OUT pin is pulled above the IN pin, input current
will typically drop to less than 2µA. This can happen if the
input of the device is connected to a discharged (low
voltage) battery and the output is held up by either a
backup battery or a second regulator circuit. The state of
the SHDN pin will have no effect on the reverse output
current when the output is pulled above the input.
6
7
LT1764-2.5
LT1764-3.3
8
9
1764 F05
10
T
V
CURRENT FLOWS INTO
OUTPUT PIN
V
V
LT1764-2.5, LT1764-3.3)
J
IN
OUT
OUT
= 25°C
= OV
= V
= V
ADJ
FB
(LT1764-1.8,
(LT1764)
1764fb