TDA7210 Infineon Technologies, TDA7210 Datasheet - Page 19

• Manufacturer Part Number: TDA7210
• Description: IC RECEIVER FSK/ASK 28-TSSOP
• Manufacturer: Infineon Technologies
• Type: ASK/FSK Single Conversion Receiverr

Specifications of TDA7210

• Package / Case: 28-TSSOP
• Frequency: 810MHz ~ 870MHz, 400MHz ~ 440MHz
• Sensitivity: -110dBm
• Data Rate - Maximum: 100 kbps
• Modulation Or Protocol: ASK, FSK
• Applications: Remote Control, RKE, Security Systems
• Current - Receiving: 5.9mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Operating Supply Voltage: 5 V
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Supply Current: 7.7 mA
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 4.5 V
• Operating Supply Voltage (typ): 5V
• Operating Supply Voltage (min): 4.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 28
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Memory Size: -
• Lead Free Status / Rohs Status: Compliant
• Other names: SP000524274; TDA7210; TDA7210INTR

Wireless Components
3.4.4
3.4.5
sary.
The oscillator signal is fed both to the synthesiser divider chain and to the down-
converting mixer. In case of operation in the 400 to 440 MHz range, the signal
is divided by two before it is fed to the mixer. This is controlled by the selection
pin FSEL (Pin 11) as described in the following table. The overall division ratio
of the divider chain can be selected to be either 128 or 64, depending on the
frequency of the reference oscillator quartz (see below and Section 4.4). The
loop filter is also realised fully on-chip.
Crystal Oscillator
The on-chip crystal oscillator circuitry allows for utilisation of quartzes both in
the 6 and 13MHz range as the overall division ratio of the PLL can be switched
between 64 and 128 via the CSEL (Pin 16) pin according to the following table.
The calculation of the value of the necessary quartz load capacitance is shown
in Section 4.3, the quartz frequency calculation is explained in Section 4.4.
Limiter
The Limiter is an AC coupled multistage amplifier with a cumulative gain of
approximately 80 dB that has a bandpass-characteristic centred around
10.7 MHz. It has a typical input impedance of 330 Ω to allow for easy interfacing
to a 10.7 MHz ceramic IF filter. The limiter circuit also acts as a Receive Signal
Strength Indicator (RSSI) generator which produces a DC voltage that is
directly proportional to the input signal level as can be seen in Figure 4-2. This
signal is used to demodulate ASK-modulated receive signals in the subsequent
baseband circuitry. The RSSI output is applied to the modulation format switch,
to the Peak Detector input and to the AGC circuitry.
In order to demodulate ASK signals the MSEL pin has to be left open as
described in the next chapter.
Table 3-2 FSEL Pin Operating States
FSEL
Open
Shorted to ground
Table 3-3 CSEL Pin Operating States
CSEL
Open
Shorted to ground
3 - 11
Crystal Frequency
RF Frequency
400-440
810-870
Data Sheet, December 2008
13.xx MHz
Functional Description
6.xx MHz
MHz
MHz
TDA7210