M22-00 Omron, M22-00 Datasheet - Page 167

• Manufacturer Part Number: M22-00
• Description: SOCKET UNIT W/OUT VOLT REDUCTION
• Manufacturer: Omron

Specifications of M22-00

• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: M2200

Precautions
Common to A22, A22S/W, A22K, M22, and A22E
Mounting
Always make sure that the power is turned OFF before mounting,
removing, or wiring the Switch, or performing maintenance.
Do not tighten the mounting ring more than necessary using tools
such as pointed-nose pliers. Doing so will damage the mounting ring.
The tightening torque is 0.98 to 1.96 N·m.
Recommended panel thickness: 1 to 5 mm.
Wiring
After wiring the Switch, maintain an appropriate clearance and
creepage distance.
When DC-specific LEDs are used, wire the Switch so that the X1 ter-
minal is positive.
Terminal screws must be Phillips or slotted M3.5 screws with a
square washer.
The tightening torque is 1.08 to 1.27 N·m.
Single wires, stranded wires, and crimp terminals can be connected
to the Switch.
Applicable Wire Size
Stranded wire: 2 mm
Solid wire: 1.6 dia. max.
Cat. No. A128-E1-03
Do not apply a voltage between the incandescent lamp and the
terminal that is greater than the rated voltage. If the incandescent
lamp is broken, the Operation Units may pop out.
Always turn OFF the power and wait for 10 minutes before replac-
ing the incandescent lamp. If the lamp is replaced immediately af-
ter the power is turned OFF, the remaining heat may cause burns.
Correct Use
!WARNING
Bare Crimp Terminals
Crimp Terminals with Insulating Sheath
16.0 mm max.
20.2 mm max.
ALL DIMENSIONS SHOWN ARE IN MILLIMETERS.
To convert millimeters into inches, multiply by 0.03937. To convert grams into ounces, multiply by 0.03527.
2
max.
8 mm max.
8 mm max.
In the interest of product improvement, specifications are subject to change without notice.
20.2 mm max.
16.0 mm max.
8 dia. max.
8 dia. max.
Operating Environment
The IP65 model is designed with a degree of protection so that it will
not sustain damage if it is subjected to water from any direction to the
front of the panel.
Using the Microload
Insert a contact protection circuit, if necessary, to prevent the reduc-
tion of life expectancy due to extreme wear on the contacts caused
by loads where inrush current occurs when the contact is opened
and closed.
The minimum applicable load is the N-level reference value. This
value indicates the malfunction reference level for the reliability level
of 60% ( 60) (conforming to JIS C5003).
The equation,
mated malfunction rate is less than 1/2,000,000 operations with a
reliability level of 60%.
LED
The LED current-limiting resistor is built-in, so internal resistance is
not required.
If commercially available LEDs are used, select the ones that meet
the following conditions:
Base: BA9S/13@
Overall length: 26 mm max.
Power consumption: 2.6 W max.
Others
If the panel is to be finished with coating, etc., make sure that the
panel meets the specified dimensions after the coating.
Do not subject the Switch to extreme shock or vibration. Doing so will
cause malfunctions and damage to the Switch.
60 = 0.5 x 10
0.16 mA
Invalid
area
1 mA
1.6 mA
Microload area
6
/operations indicates that the esti-
10 mA
100 mA
Current (mA)
Standard
load area
165