MC9S08MM128VLH Freescale Semiconductor, MC9S08MM128VLH Datasheet - Page 19

• Manufacturer Part Number: MC9S08MM128VLH
• Description: IC MCU 8BIT 128K FLASH 64LQFP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08MM128VLH

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 48MHz
• Connectivity: I²C, SCI, SPI, USB
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 33
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 12K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 6x16b, D/A 1x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 105°C
• Package / Case: 64-LQFP
• Processor Series: S08MM
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 12 KB
• Maximum Clock Frequency: 48 MHz
• Operating Supply Voltage: - 0.3 V to + 3.8 V
• Maximum Operating Temperature: + 105 C
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: TWR-SER, TWR-ELEV, TWR-S08MM128-KIT, TWR-SENSOR-PAK, TWR-MCF51MM-KIT, TWR-LCD
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 16 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Freescale Semiconductor
Freescale reserves the right to change the detail specifications as may be required to permit improvements in the design of its products.
1
2
3
4
5
6
7
8
9
10
11
Num Symbol
20
21
22
23
Typical values are measured at 25C. Characterized, not tested
As the supply voltage rises, the LVD circuit will hold the MCU in reset until the supply has risen above V
Does not include analog module pins. Dedicated analog pins should not be pulled to V
floating when not used to reduce current leakage.
Measured with V
All functional non-supply pins are internally clamped to V
Input must be current limited to the value specified. To determine the value of the required current-limiting resistor,
calculate resistance values for positive and negative clamp voltages, then use the larger of the two values.
Power supply must maintain regulation within operating V
current conditions. If positive injection current (V
and could result in external power supply going out of regulation. Ensure external V
than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are:
if no system clock is present, or if clock rate is very low (which would reduce overall power consumption).
Maximum is highest voltage that POR is guaranteed.
Run at 1 MHz bus frequency
Low voltage detection and warning limits measured at 1 MHz bus frequency.
Factory trimmed at V
V
V
V
V
LVWH
LVWL
hys
BG
Low-voltage
warning
threshold —
high range
Low-voltage
warning
threshold —
low range
Low-voltage inhibit reset/recover
hysteresis
Bandgap Voltage Reference
In
= V
DD
DD
9
= 3.0 V, Temp = 25C
Characteristic
10
.
9
Table 9. DC Characteristics (Continued)
V
V
V
V
DD
DD
DD
DD
falling
rising
falling
rising
11
In
> V
DD
Condition
) is greater than I
SS
—
—
—
—
—
—
DD
and V
range during instantaneous and operating maximum
DD
except PTD1.
2.36
2.36
2.11
2.16
1.15
DD
Min
—
, the injection current may flow out of V
DD
Typ
2.46
2.46
2.16
2.23
1.17
50
load will shunt current greater
DD
1
or V
Electrical Characteristics
Max
2.56
2.56
2.22
2.27
1.18
SS
—
and should be left
Unit
mV
LVDL
V
V
V
V
V
.
C
C
P
P
P
P
P
DD
19