PIC18F2423-I/ML Microchip Technology, PIC18F2423-I/ML Datasheet - Page 32

• Manufacturer Part Number: PIC18F2423-I/ML
• Description: 16KB, Flash, 768bytes-RAM, 25I/O, 8-bit Family,nanoWatt 28 QFN 6x6mm TUBE
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F2423-I/ML

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 25
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 28-VQFN Exposed Pad, 28-HVQFN, 28-SQFN, 28-DHVQFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT28QFN4 - SOCKET TRANS ICE 28QFN W/CABLEAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

PIC18F2423/2523/4423/4523
2.4
The selection of the automatic acquisition time and A/D
conversion clock is determined in part by the clock
source and frequency while in a power-managed mode.
If the A/D is expected to operate while the device is in
a power-managed mode, the ADCS<2:0> bits in
ADCON2 should be updated in accordance with the
clock source to be used. The ACQT<2:0> bits do not
need to be adjusted as the ADCS<2:0> bits adjust the
T
mode, an A/D acquisition or conversion may be started.
Once started, the device should continue to be clocked
by the same clock source until the conversion has been
completed.
If desired, the device may be placed into the
corresponding Idle mode during the conversion. If the
device clock frequency is less than 1 MHz, the A/D RC
clock source should be selected.
Operation in Sleep mode requires the A/D F
be selected. If bits, ACQT<2:0>, are set to ‘000’ and a
conversion is started, the conversion will be delayed
one instruction cycle to allow execution of the SLEEP
instruction and entry to Sleep mode. The IDLEN bit
(OSCCON<7>) must have already been cleared prior
to starting the conversion.
DS39755C-page 32
AD
time for the new clock speed. After entering the
Operation in Power-Managed
Modes
RC
clock to
2.5
The ADCON1, TRISA, TRISB and TRISE registers all
configure the A/D port pins. The port pins needed as
analog inputs must have their corresponding TRIS bits
set (input). If the TRIS bit is cleared (output), the digital
output level (V
The A/D operation is independent of the state of the
CHS<3:0> bits and the TRIS bits.
Note 1: When reading the PORT register, all pins
2: Analog levels on any pin defined as a
3: The
Configuring Analog Port Pins
configured as analog input channels will
read as cleared (a low level). Analog con-
version on pins configured as digital pins
can be performed. The voltage on the pin
will be accurately converted.
digital input may cause the digital input
buffer to consume current out of the
device’s specification limits.
Register 3H configures PORTB pins to
reset as analog or digital pins by controlling
how the PCFG<3:0> bits in ADCON1 are
reset.
OH
or V
PBADEN
OL
© 2009 Microchip Technology Inc.
) will be converted.
bit
in
Configuration