H3CR-A8E 100-240VAC/100-125VD Omron, H3CR-A8E 100-240VAC/100-125VD Datasheet - Page 5

• Manufacturer Part Number: H3CR-A8E 100-240VAC/100-125VD
• Description: Solid State Timer
• Manufacturer: Omron

Specifications of H3CR-A8E 100-240VAC/100-125VD

• Contact Configuration: SPDT
• Nom Input Voltage: 240VAC
• Timing Adjustment: Knob
• Relay Mounting: DIN Rail

H3CR-A
Note: When the time setting knob is turned below “0” until the point where the time setting knob stops, the output will operate instantaneously
Standard (0.05-s to 300-h) Models
Double (0.1-s to 600-h) Models
Note: 1. DC ripple rate: 20% max. if the power supply incorporates a single-phase, full-wave rectifier.
Time unit
Full scale
setting
Time unit
Full scale
setting
Rated supply voltage (see note 1)
Operating voltage range
Power reset
Input
Power consumption
Control outputs
Time Ranges
Ratings
tti
tti
at all time range settings.
2. Each 24-to-48-VAC/12-to-48-VDC model causes an inrush current of approximately 0.85 A. Pay careful attention when attempting
3. The values are for when the terminals 2 and 7 and terminals 10 and 6 are short-circuited, and include the consumption current of the
to turn ON power to such a model with non-contact output from a device such as a sensor.
input circuit.
1.2
3
12
30
2.4
6
24
60
0.05 to 1.2
0.3 to 3
1.2 to 12
3 to 30
0.1 to 2.4
0.6 to 6
2.4 to 24
6 to 60
s (sec)
s (sec)
100 to 240 VAC (50/60 Hz)/100 to 125 VDC, 24 to 48 VAC (50/60 Hz)/12 to 48 VDC (24 to
48 VAC/VDC for H3CR-A8E) (see note 2)
85% to 110% of rated supply voltage (90% to 110% at 12 VDC)
Minimum power-opening time: 0.1 s
No-voltage Input
ON impedance:
ON residual voltage: 1 V max.
OFF impedance:
Voltage Input
Max. permissible capacitance between inputs lines (terminals 6 and 7): 1,200 pF
Load connectable in parallel with inputs (terminals 6 and 7).
•
H3CR-A/-A8
•
H3CR-AP (see note 3)
•
H3CR-A8E
•
H3CR-AS/-A8S
•
Time limit contacts:
Transistor output:
Instantaneous contact: 5 A at 250 VAC, resistive load (cosφ = 1)
•
•
•
•
100 to 240 VAC/100 to 125 VDC
High (logic) level: 85 to 264 VAC/85 to 137.5 VDC
Low (logic) level: 0 to 10 VAC/0 to 10 VDC
24 to 48 VAC/12 to 48 VDC
High (logic) level: 20.4 to 52.8 VAC/10.8 to 52.8 VDC
Low (logic) level: 0 to 2.4 VAC/0 to 1.2 VDC
100 to 240 VAC/100 to 125 VDC
(When at 240 VAC, 60 Hz)
24 to 48 VAC/12 to 48 VDC
(When at 24 VDC)
100 to 240 VAC/100 to 125 VDC
(When at 240 VAC, 60 Hz)
24 to 48 VAC/12 to 48 VDC
(When at 24 VDC)
100 to 240 VAC/100 to 125 VDC
(When at 240 VAC, 60 Hz)
24 to 48 VAC/VDC
(When at 24 VDC)
24 to 48 VAC/12 to 48 VDC
(When at 24 VDC)
0.12 to 1.2
0.24 to 2.4
Relay ON: approx. 2.1 VA (1.6 W) Relay OFF: approx. 1.3 VA (1.1 W)
Relay ON: approx. 0.8 W
Relay ON: approx. 2.5 VA (2.2 W) Relay OFF: approx. 1.8 VA (1.7 W)
Relay ON: approx. 0.9 W
Relay ON/OFF: approx. 2 VA (0.9 W)
Relay ON/OFF: approx. 0.9 W
Output ON: 0.3 W Output OFF: 0.2 W
1 kΩ max.
100 kΩ min.
5 A at 250 VAC/30 VDC, resistive load (cosφ = 1)
Open collector (NPN/PNP), 100 mA max. at 30 VDC max.,
residual voltage: 2 V max.
min
min
Relay OFF: approx. 0.2 W
Relay OFF: approx. 0.3 W
h (hrs)
h (hrs)
1.2 to 12
3 to 30
12 to 120
30 to 300
2.4 to 24
6 to 60
24 to 240
60 to 600
x10 h (10 h)
x10 h (10 h)
H3CR-A
7