AS5163-HTST-500 austriamicrosystems, AS5163-HTST-500 Datasheet - Page 30

• Manufacturer Part Number: AS5163-HTST-500
• Description: IC ENCODER ROTARY 14-TSSOP
• Manufacturer: austriamicrosystems
• Type: Linear, Rotary Encoder - Programmabler

Specifications of AS5163-HTST-500

• Featured Product: AS5163 - Contactless Magnetic Angle Position Sensor
• Sensing Range: 30mT ~ 70mT
• Voltage - Supply: 4.5 V ~ 5.5 V
• Current - Supply: 20mA
• Output Type: Analog, Ratiometric
• Operating Temperature: -40°C ~ 150°C
• Package / Case: 14-TSSOP (0.173", 4.40mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output (max): -
• Features: -
• Other names: AS5163-HTST-500TR

AS5163
Datasheet - A p p l i c a t i o n I n f o r m a t i o n
8.2.1 Read / Write User Data
Table 17. Read / Write Data
Data Content:
Data only for read:
Data for write and read:
8.2.2 Programming Procedure
Note: After programming the OTP fuses, a verification is mandatory. The procedure described below must be strictly followed to ensure
For further information, please refer to Application Note AN5163-10 available at
www.austriamicrosystems.com/AS5163
Read and Write
Region
Read only
Area
CORDIC_OUT(13:0): 14-bit absolute angular position data.
OCF (Offset Compensation Finished): logic high indicates the finished Offset Compensation Algorithm. As soon as this bit is set, the
AS5163 has completed the startup and the data is valid.
COF (Cordic Overflow): Logic high indicates an out of range error in the CORDIC part. When this bit is set, the CORDIC_OUT(13:0) data is
invalid. The absolute output maintains the last valid angular value. This alarm may be resolved by bringing the magnet within the X-Y-Z
tolerance limits.
AGC_VALUE (7:0): magnetic field indication.
DSP_RES resets the DSP part of the AS5163 the default value is 0. This is active low. The interface is not affected by this reset.
R1K_10K defines the threshold level for the OTP fuses. This bit can be changed for verification purpose. A verification of the programming
of the fuses is possible. The verification is mandatory after programming.
Pull-up / Pull-down on OUT pin
VDD=5V
Wait startup time, device enters communication mode
Write128 command: The trimming bits are written in the SFR memory.
Read128 command: The trimming bits are read back.
Upload command: The SFR memory is transferred into the OTP RAM.
Fuse command: The OTP RAM is written in the Poly Fuse cells.
Wait fuse time (6 ms)
Write command (R1K_10K=1): Poly Fuse cells are transferred into the RAM cells compared with 10KΩ resistor.
Download command: The OTP RAM is transferred into the SFR memory.
Read128 command: The fused bits are read back.
Write command (R1K_10K=0): Poly Fuse cells are transferred into the RAM cells compared with 1KΩ resistor.
Download command: The OTP RAM is transferred into the SFR memory.
Read128 command: The fused bits are read back.
Pass2Func command or POR: Go to Functional mode.
properly programmed OTP fuses.
Address
0x10
0x11
0x12
0x17
Address
16
17
18
23
OCF
Bit7
0
COF
Bit6
0
Revision 2.7
Bit5
0
www.austriamicrosystems.com
CORDIC_OUT[7:0]
AGC_VALUE[7:0]
Bit4
0
CORDIC_OUT[13:8]
Bit3
0
Bit2
0
DSP_RES R1K_10K
Bit1
Bit0
30 - 36