PTFM04BH471Q2N34B0 Murata, PTFM04BH471Q2N34B0 Datasheet - Page 87

• Manufacturer Part Number: PTFM04BH471Q2N34B0
• Description: PTC THERMISTOR
• Manufacturer: Murata
• Series: PTFMr
• Type: PTCr

Specifications of PTFM04BH471Q2N34B0

• Thermistor Type: PTC
• Resistance: 100ohm
• Operating Temperature Range: -10°C To +70°C
• Operating Voltage Range: 16V
• Thermistor Case Style: Radial Lead
• No. Of Pins: 2
• Length/height, External: 13.2mm
• External Width: 7.5mm
• Tolerance: 20 %
• Termination Style: Radial
• Current Rating: 0.1 Amp
• Dimensions: 4 mm Dia.
• Voltage: 16 V
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

!Note
1. Solder and Flux
2. Cleaning Conditions and Drying
3. Soldering Conditions
Notice (Soldering and Mounting) PRG Series
(1) Solder Paste
To remove the flux after soldering, observe the following
points in order to avoid deterioration of the characteristics
or any change to the external electrode's quality.
(1) Cleaning Conditions
A sufficient cleaning should be applied to remove flux completely.
(2) Drying
In your mounting process, observe the following points in
order to avoid deterioration of the characteristics or
destruction of this product. The mounting quality of this
product may also be affected by the mounting conditions,
shown in the points below.
This product is for reflow soldering only. Flow soldering
should not be allowed.
(1) Printing Conditions of Solder Paste
(a) Standard thickness of solder paste printing should
(b) After soldering, the solder fillet should be a height
(c) Too much solder cause strong mechanical stress to
Use solder paste Sn:Pb=63:37wt%.
For your reference, we are using
manufactured by Alpha Metals Japan Ltd.
manufactured by Senju Metal Industry Co., LTD for any
internal tests of this product.
After cleaning, promptly dry this product.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please review our product specifications or consult the approval sheet for product specifications before ordering.
be from 0.15 to 0.20 mm.
from 0.2 mm to the thickness of this product (see the
figure at right).
this product. Such stress may cause cracking or other
mechanical damage. Also, it can destroy the
electrical performance of this product.
2-propanol
Solvent
63Sn/37Pb RMA9086 90-3-M18,
96.5Sn/3.0Ag/0.5Cu M705-GRN360-K2-V,
Less than 5 minutes
Less than 2 minutes
Dipping Cleaning
at room temp.
at 40˚C max.
or
Ultrasonic Cleaning
Less than 1 minute
20W/L Frequency
of several 10kHz
to 100kHz.
(2) Flux
E
• Strong acidic flux (with halide content exceeding
• Water-soluble flux
Use rosin type flux in the soldering process.
If below flux is used, some problems might be caused
in the product characteristics and reliability.
Please do not use the flux listed below.
0.2wt%).
(*Water-soluble flux can be defined as non rosin type
flux including wash-type flux and non-wash-type flux.)
Electrode
Solder
!Caution/Notice
Continued on the following page.
T
Solder
0.2mm V T V E
85
Apr.25,2011
R90E.pdf
12