C48CB003 Red Lion Controls, C48CB003 Datasheet - Page 3

• Manufacturer Part Number: C48CB003
• Description: C48C (3P,R,SNK,RLY)
• Manufacturer: Red Lion Controls
• Type: Counterr

Specifications of C48CB003

• Rohs Compliant: YES
• Connection Type: Screw
• Cut Out, Panel: 1/16 DIN
• Digit Height: 0.3
• Dimensions: 4.17"L×1.95"W×1.95"H
• Display Digit Height: 0.3" (Main), 0.2" (Secondary)
• Display Type: LCD
• Function: Counter
• Material, Casing: Plastic
• Number Of Digits: 6
• Primary Type: Electronic
• Range, Measurement: 0.00001 to 9.99999
• Special Features: programmable
• Voltage, Supply: 85 to 250 VAC
• Sealing: NEMA 4X/IP65
• Power Requirements: 85 to 250 VAC
• Operating Temperature: 0 to +50°C
• Panel Cutout: 1.77" × 1.77" (1⁄16 DIN)
• Lead Free Status / Rohs Status: RoHS Compliant part

8. OUTPUTS: (Output type and quantity, model dependent) Cont’d
9. RS485 SERIAL COMMUNICATIONS (Optional): Up to 32 units can be
10. CERTIFICATIONS AND COMPLIANCES:
11. ENVIRONMENTAL CONDITIONS:
12. ELECTRICAL CONNECTIONS: Wire clamping screw terminals.
13. CONSTRUCTION: Black plastic case with collar style panel latch. The
14. WEIGHT: 6.0 oz (170 g)
Relay: Form A contact, Rating = 5 A @ 250 VAC, 30 VDC (resistive load),
Programmable Timed Output: User selectable output time resolution.
Note: For Prescaler values above 2, the timed delay output is affected by
connected.
Baud Rate: Programmable from 1200 to 9600 baud
Address: Programmable from 0 to 99
Data Format: 10 Bit Frame, 1 start bit, 7 or 8 data bits, 1 or No Parity bit,
Parity: Programmable for Odd (7 data bits), Even (7 data bits), or None (8
UL Recognized Component, File #E137808
ELECTROMAGNETIC COMPATIBILITY
Notes:
AC VERSIONS
1. A power line filter, RLC#LFIL0000 or equivalent, was installed when the
DC VERSIONS
Refer to EMC Installation Guidelines section of the manual for additional
Operating Temperature: 0°C to 50°C
Storage Temperature: -40°C to 70°C
Operating and Storage Humidity: 85% max. relative humidity
(non-condensing) from 0°C to 50°C.
Altitude: Up to 2000 meters
panel latch can be installed for horizontal or vertical stacking. Black plastic
textured bezel with clear display viewing window. Unit assembly with circuit
boards can be removed from the case without removing the case from the
panel or disconnecting the wiring. Front panel meets NEMA 4X/IP65
requirements for indoor use, when properly installed. Installation Category
II, Pollution Degree 2.
Immunity to EN 50082-2
Electrostatic discharge
Electromagnetic RF fields
Fast transients (burst)
RF conducted interference
Simulation of cordless telephone
Emissions to EN 50081-2
RF interference
1/10 HP @ 120 VAC (inductive load)
Relay Life Expectancy: 100,000 cycles min. at max. load rating
0.01 Second Resolution: 0.01 to 99.99 sec, ± 0.01% +20 msec max.
0.1 Second Resolution: 0.1 to 999.9 sec, ± 0.01% + 100 msec (Prescalers
the count speed (rate).
and 1 stop bit
data bits)
Recognized to U.S. and Canadian requirements under the Component
Recognition Program of Underwriters Laboratories, Inc.
unit was DC powered.
To insure compliance with the EMC standards listed above, do not connect
any wires from the terminal(s) labeled “COMM.” to the “DC-” supply
terminal (12), when powering the unit from a DC supply.
information.
(Prescalers less than 2)
less than 2)
EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-6
ENV 50204
EN 55011
Level 2; 4 Kv contact
Level 3; 8 Kv air
Level 3; 10 V/m
80 MHz - 1 GHz
Level 4; 2 Kv I/O
Level 3; 2 Kv power
Level 3; 10 V/rms
150 KHz - 80 MHz
Level 3; 10 V/m
900 MHz ± 5 MHz
200 Hz, 50% duty cycle
Enclosure class A
3
SINGLE PRESET MODELS
output. The solid-state output is available as an NPN or PNP open collector
transistor.
DUAL PRESET MODELS
respectively. These outputs can be relay outputs, or solid-state outputs. The
solid-state outputs are available as NPN or PNP open-collector transistors. Units
with solid-state outputs can be ordered with an optional prescaler output
(C48CP).
3 PRESET BATCH MODELS
to keep a total count. This second counter can be programmed to operate in one
of eight operating modes. Outputs 1 and 2 are assigned to the primary process
counter (C1). Output 3 is assigned to the secondary Batch/Total counter (C2).
The three preset batch unit can be ordered with solid-state or relay outputs.
Units with solid-state outputs have a User Input 2 terminal available. The relay
model has a relay output for Output 2 and Output 3 (Batch/Total). Output 1 is
available only as solid-state.
PRESCALER OUTPUT MODELS
have an additional output configured as a prescaler output. Each time the least
significant digit of the display increments, the Prescaler output provides a pulse.
The width of this pulse is variable in that the output will turn off after a
programmed number of count input pulses has occurred (1-9). The Prescaler
output can also be programmed to activate when the 10’s digit of the display
increments, rather than the least significant digit.
Note: Prescaler Output models are limited to two programmable count modes
FRONT PANEL FEATURES
(main display), the count or batch/total value is shown on the top line and
presets, prescaler, or output time values are shown on the bottom line. The
bottom line values can be programmed to be viewable only, viewable and
changeable, or locked (not viewable) from the main display.
accessible providing that these values are not programmed for ‘L’ocked. Values
that are accessible (changeable) can be changed immediately when viewed in
the secondary display.
The C48CS has a solid-state output that operates in parallel with a relay
The C48CD has two outputs that are activated from presets 1 and 2
The C48CB has a secondary counter that can be used for batch counting, or
The C48CP is a dual preset counter with solid-state outputs. These models
and prescaler values of 1.00000 or less. See Count Input Modes for available
modes.
The C48 Counters feature a dual line display. In the normal operating mode
In the operating mode, the presets, prescaler, and output time values are
!
"
#
$
- Performs user Programmed Function
- Cycles through secondary displays.
- Enters Protected Value Menu or Programming Mode
- Scrolls through programming parameters.
- Enters Data Values.
- Selects next available mode in programming mode.
- Increments digit in Digit Entry mode.
- Increments value in Auto Scrolling entry mode.
- Selects Digit to right when in Digit Entry mode.
- Decrements value in Auto Scrolling entry mode.
when pushed and held for 2 seconds.
FRONT PANEL KEYPAD