10250T201NC2N EATON CUTLER HAMMER, 10250T201NC2N Datasheet - Page 177

• Manufacturer Part Number: 10250T201NC2N
• Description: INDICATOR, INCAND LAMP, BAYONET
• Manufacturer: EATON CUTLER HAMMER

Specifications of 10250T201NC2N

• Base Type: Bayonet
• Supply Voltage: 120V
• Current Rating: 6A
• Contact Current Max: 6A
• Illumination: Illuminated
• Switch Features: Resistor
• Actuator Style: Pushbutton
• Color: Green
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Contact Block Operation
Contact blocks mount directly to the back of the operator. For
reliable operation, the maximum number of contact blocks that
should be installed behind each operator lever is two (four total).
The figure below identifies the circuits activated by each of the
eight possible lever positions. Contact block plungers 1, 2, 3, 4
are depressed (change state) when handle is in the position
indicated by arrows below.
Circuit Activation
Note: Joystick in its resting state, center position, does not activate
contact block plungers.
Ordering Example:
Suppose you are looking for a four-position momentary joystick
without a latch and the following circuit arrangements.
X = Closed Circuit, O = Open Circuit.
Example Circuit Arrangements
Circuit
1st
2nd
The contact blocks and their mounting locations would be as
follows:
Example Contact Blocks and Locations
A complete bill of material for this example would include:
Example Order
Qty.
1
2
2
Catalog Number
10250T451
10250T2
10250T1
10250T1 10250T2
10250T1 10250T2
Circuit
2nd
NO
NC
NC
NO
Up
X
X
1
2
3
4
Circuit
1st
NO
NO
NO
NO
Down
X
O
Left
X
O
Right
X
X
Pushbuttons and Indicating Lights
Control Products Catalog CA08102001E—August 2010 www.eaton.com
30.5 mm Heavy-Duty Watertight/Oiltight—10250T
Blank Legend Plates for Joystick Operators
When ordering engraved legend plates, order by catalog number
and insert the following into order notes:
●
●
●
Locations K and M can accommodate up to two lines
horizontally; L and N up to two lines vertically.
Maximum number of characters:
●
●
Ordering Example:
Two-position legend plate to be marked “UP” “DOWN.”
Catalog No. 10250TJ2S4STAMP
Letter Size: 3/16 in (4.8 mm)
Pos. K—UP
Pos. M—DOWN
Two-Position
Catalog Number
Blank Plate
10250TJS3
Engraved Plate
10250TJS3STAMP
Four-Position
Catalog Number
Blank Plate
10250TJS1
Engraved Plate
10250TJS1STAMP
(55.6)
2.19
Sq.
E
Legend required
Size of characters: 3/16,
1/8, 3/32 in (4.8, 3.2, 2.4 mm)
Location by letter (A–N)
Horizontal
3/16 in—13, 1/8 in—14, 3/32 in—19
Vertical
3/16 in—10, 1/8 in—13, 3/32 in—14
C
G
A
B
J
L
D
H
F
M
K
N
Catalog Number
10250TJS2
10250TJS2STAMP
E
Catalog Number
10250TJS4
10250TJS4STAMP
C
G
A
B
J
D
H
M
K
F
47.6
177
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47
47