ENW-C9A21A4EF Panasonic - ECG, ENW-C9A21A4EF Datasheet - Page 31

• Manufacturer Part Number: ENW-C9A21A4EF
• Description: RF MODULE 802.15.4 W/ANT SNAP
• Manufacturer: Panasonic - ECG
• Series: PAN4561r

Specifications of ENW-C9A21A4EF

• Frequency: 2.4GHz
• Data Rate - Maximum: 250kbps
• Modulation Or Protocol: 802.15.4
• Applications: General Purpose
• Power - Output: 0dBm
• Sensitivity: -92dBm
• Voltage - Supply: 2.7 V ~ 3.4 V
• Current - Receiving: 45mA
• Current - Transmitting: 43mA
• Data Interface: PCB, Surface Mount
• Memory Size: 60kB Flash, 4kB RAM
• Antenna Connector: On-Board, Chip
• Operating Temperature: -40°C ~ 85°C
• Package / Case: Module
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ENW-C9A21A4EF; ENWC9A21A4EF; P14522TR; PAN4560; PAN4561L; Q5659594

CLASSIFICATION
SUBJECT
CUSTOMER’S CODE
PAN4561H /M /L
PANASONIC ELECTRONIC DEVICES EUROPE GMBH
27.2. CAUTION
27.3. LABELING REQUIREMENTS
27.4. ANTENNA WARNING
PAN4561L
No restrictions
Operation is subject to the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received, including
interference that may cause undesired operation.
The FCC requires the user to be notified that any changes or modifications made to this
device that are not expressly approved by Panasonic Electronic Devices Europe GmbH
may void the user's authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
The Original Equipment Manufacturer (OEM) must ensure that FCC labeling requirements
are met. This includes a clearly visible label (laser marking) on the outside of the OEM
enclosure specifying the appropriate Panasonic FCC identifier for this product as well as
the FCC Notice above. The FCC identifier is FCC ID: T7V4561HM.
In any case end product must be labelled exterior with "Contains FCC ID: T7V4561HM"
The related part number for this device is ENWC9A2xBxEF (PAN4561 with U.FL
connector) and ENWC9A2xCxEF (PAN4561 with SMD pad). For details, please see the
chapter 24. Ordering Information. This device is tested with a standard SMA connector and
with the antennas listed below. When integrated in the OEMs product, these fixed antennas
require installation preventing end-users from replacing them with non-approved antennas.
Any antenna not in the following table must be tested to comply with FCC Section 15.203
for unique antenna connectors and Section 15.247 for emissions. The FCC identifier for
this device with the antenna listed in item 1 are the same (FCC ID: T7V4561HM).
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
Consult the dealer or an experienced radio/TV technician for help
receiver is connected.
MODEM FOR 802.15.4 IEEE STANDARD
PRODUCT SPECIFICATION
PANASONIC PART NUMBER
ENWC9A22xxEF / .25xx. / .21xx.
No.
DS-4561-2400-102
PAGE
DATE
www.pedeu.pansonic.de
06.08.2010
31 of 34
REV.
G