NCP18XH103K0SRB Murata, NCP18XH103K0SRB Datasheet - Page 53

• Manufacturer Part Number: NCP18XH103K0SRB
• Description: Thermistors - NTC 10K OHM 10%
• Manufacturer: Murata
• Type: NTCr
• Series: NCPr

Specifications of NCP18XH103K0SRB

• Description Of Terminals: Leadless
• Mounting Style: Surface Mount
• Pin Count: 2
• Screening Level: Automotive
• Resistance @ 25c: 10kohm
• Percentage Of Resistance Tolerance @ 25c: ±10
• Accuracy: ±1
• Operating Temperature Min Deg. C: -40C
• Operating Temperature Max Deg. C: 125C
• Product Length (mm): 1.6mm
• Product Height (mm): 0.8mm
• Product Depth (mm): 0.8mm
• Resistance: 10 KOhms
• Tolerance: 10 %
• Operating Temperature Range: - 40 C to + 125 C
• Package / Case: 0603
• Current Rating: 0.31 mAmp
• Power Rating: 100 mW
• Lead Free Status / RoHS Status: Compliant

6
!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
This product is designed for application in an
ordinary environment (normal room temperature,
humidity and atmospheric pressure). Do not use under
the following conditions because all these factors
can deteriorate the characteristics or cause product
failure and burn-out.
1. Corrosive gas or deoxidizing gas (Chlorine gas,
Be sure to provide an appropriate fail-safe function
on your product to prevent secondary damage that may be
caused by the abnormal function or the failure of our
product.
To keep solderability of product from declining,
following storage condition is recommended.
1. Storage condition:
2. Storage term:
When the lead of this product is soldered, pay
attention as follows to avoid the decline of element
characteristics or break-down of the element.
1. Use Rosin type flux or non-activated flux
2. Do not dip the body into flux (flux should be coated
3. Be sure that preheating does not melt the
1. Do not apply an excessive force to the lead.
2. This product does not have waterproof
52
POSISTORr Lead Type for Overheat Protection !Caution/Notice
to lead wire only for soldering).
!Caution (Storage and Operating Condition)
Hydrogen sulfide gas, Ammonia gas, Sulfuric acid
gas, Nitric oxide gas, etc.)
!Caution (Other)
Notice (Storage and Operating Condition)
Temperature -10 to +40 degrees C
Humidity less than 75%RH (not dewing condition)
Use this product within 6 months after delivery
by first-in and first-out stocking system.
Notice (Soldering and Mounting)
soldering of this product.
Notice (Handling)
Otherwise, it may cause the junction between lead
and element to break, or may crack the element.
Therefore, holding the element side lead wire is
recommended when lead wire is bent or cut.
construction. Splashed water may cause failure
mode such as decline of characteristics or current
leak.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. Volatile or flammable gas
3. Dusty conditions
4. Under vacuum, or under high or low-pressure
5. Wet or humid conditions
6. Places with salt water, oils, chemical liquids or
7. Strong vibrations
8. Other places where similar hazardous conditions
3. Handling after unpacking:
4. Storage place:
3. When this product is operated, temperature of some
organic solvents
exist
After unpacking, promptly reseal this product or
store it in a sealed container with a drying agent.
Do not store this product in corrosive gas
(Sulfuric acid, Chlorine, etc.) or in direct
sunlight.
areas may be over 100 to 160 degrees C. Be sure that
surrounding parts and inserting material can
withstand the temperature. If the surrounding part
and material are kept under such conditions, they
may deteriorate or produce harmful gas
(Chlorine gas, Hydrogen sulfide gas, Ammonia gas,
Sulfuric acid gas, Nitric oxide gas, etc.). And
such harmful gas may deteriorate the element.
R03E.pdf
07.3.21