AD976AR Analog Devices Inc, AD976AR Datasheet - Page 8

• Manufacturer Part Number: AD976AR
• Description: A/D Converter (A-D) IC
• Manufacturer: Analog Devices Inc

Specifications of AD976AR

• Package/case: 28-SOIC
• Features: 16?Bit, Serial, 100kSPS ADC
• Interface Type: Parallel
• Leaded Process Compatible: No
• Number Of Bits: 16
• Number Of Channels: 1
• Peak Reflow Compatible (260 C): No
• Rohs Status: RoHS non-compliant
• Sampling Rate (per Second): 200k
• Data Interface: Parallel
• Number Of Converters: 1
• Power Dissipation (max): 100mW
• Voltage Supply Source: Analog and Digital
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 28-SOIC (0.300", 7.50mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• For Use With: EVAL-AD976CB - BOARD EVAL FOR AD976EVAL-AD976ACB - BOARD EVAL FOR AD976A
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

AD976/AD976A
CONVERSION CONTROL
The AD976/AD976A is controlled by two signals: R/C and CS,
as shown in Figures 2 and 3. To initiate a conversion and place
the sample/hold circuit into the hold state, both the R/C and CS
signals must be brought low for no less than 50 ns. Once the
conversion process begins, the BUSY signal will go Low until
the conversion is complete. At the end of a conversion, BUSY
will return High, and the resulting valid data will be available on
the data bus. On the first conversion after the AD976/AD976A
is powered up, the DATA output will be indeterminate.
The AD976/AD976A exhibits two modes of conversion. In the
mode demonstrated in Figure 2, conversion timing is controlled
by a negative-going R/C signal, at least 50 ns wide. In this mode
the CS pin is always tied low, and the only limit placed on how
long the R/C signal can remain low is the desired sampling rate.
Less than 83 ns after the initiation of a conversion, the BUSY
signal will be brought low and remain low until the conversion is
complete and the output shift registers have been updated with
the new Binary Twos Complement data.
Figure 2. Conversion Timing with Outputs Enabled After Conversion ( CS Tied Low)
MODE
BUSY
DATA
BUS
R/C
CS
MODE
BUSY
DATA
BUS
R/C
ACQUIRE
Figure 3. Using CS to Control Conversion and Read Timing
t
12
DATA VALID
ACQUIRE
PREVIOUS
t
1
t
6
t
3
t
t
9
3
t
t
1
6
HI-Z
t
12
t
t
14
11
CONVERT
CONVERT
DATA VALID
t
t
PREVIOUS
7
4
t
t
2
7
t
–8–
4
t
13
Figure 3 demonstrates the AD976/AD976A conversion timing,
using CS to control both the conversion process and the reading
of output data. To operate in this mode, the R/C signal should
be brought low no less than 10 ns before the falling edge of a CS
pulse (50 ns wide) is applied to the ADC. Once these two pulses
are applied, BUSY will go low and remain low until a conver-
sion is complete. After a maximum of 4 s (AD976A only),
BUSY will again return high, and parallel data will be valid on
the ADC outputs. To achieve the maximum 100 kHz/200 kHz
throughput rate of the part, the negative going R/C and CS
control signals should be applied every 5 s (AD976A). It should
also be noted that although all R/C and CS commands will be
ignored once a conversion has begun, these inputs can be
asserted during a conversion; i.e., a read during conversion can
be performed. Voltage transients on these inputs could feed
through to the analog circuitry and affect conversion results.
VALID
NOT
t
ACQUIRE
5
HI-Z
DATA
VALID
ACQUIRE
t
8
t
t
10
12
t
14
HI-Z
t
1
DATA VALID
CONVERT
t
VALID
DATA
t
9
12
HI-Z
REV. C