ADSP-21065LKSZ-264 Analog Devices Inc, ADSP-21065LKSZ-264 Datasheet - Page 10

• Manufacturer Part Number: ADSP-21065LKSZ-264
• Description: ADSP-21065L 66MHz
• Manufacturer: Analog Devices Inc
• Series: SHARC®r
• Type: Fixed/Floating Pointr

Specifications of ADSP-21065LKSZ-264

• Interface: Host Interface, Serial Port
• Clock Rate: 60MHz
• Non-volatile Memory: External
• On-chip Ram: 64kB
• Voltage - I/o: 3.30V
• Voltage - Core: 3.30V
• Operating Temperature: 0°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 208-MQFP, 208-PQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

ADSP-21065L
Pin
SDA10
XTAL
PWM_EVENT
VDD
GND
NC
CLOCK SIGNALS
The ADSP-21065L can use an external clock or a crystal. See
CLKIN pin description. You can configure the ADSP-21065L
to use its internal clock generator by connecting the necessary
components to CLKIN and XTAL. You can use either a crystal
operating in the fundamental mode or a crystal operating at an
overtone. Figure 4 shows the component connections used for a
crystal operating in fundamental mode, and Figure 5 shows
the component connections used for a crystal operating at an
overtone.
Figure 4. 30 MHz Operation (Fundamental Mode Crystal)
Figure 5. 30 MHz Operation (3rd Overtone Crystal)
SUGGESTED COMPONENTS FOR 30 MHz OPERATION:
NOTE: C1 AND C2 ARE SPECIFIC TO CRYSTAL SPECIFIED FOR X1.
SUGGESTED COMPONENTS FOR 30MHz OPERATION:
NOTE: C1, C2, C3, R
ECLIPTEK EC2SM-33-30.000M (SURFACE MOUNT PACKAGE)
ECLIPTEK EC-33-30.000M (THROUGH-HOLE PACKAGE)
ECLIPTEK EC2SM-T-30.000M (SURFACE MOUNT PACKAGE)
ECLIPTEK ECT-30.000M (THROUGH-HOLE PACKAGE)
CONTACT CRYSTAL MANUFACTURER FOR DETAILS.
C1 = 33pF
C2 = 27pF
C1 = 18pF
C2 = 27pF
C3 = 75pF
FOR X1. CONTACT MANUFACTURER FOR DETAILS.
L
R
C1
CLKIN
1
S
= 3300nH
= SEE NOTE.
1-0
C1
CLKIN
S
AND L
Type
O/T
O
I/O/A
P
G
X1
1
ARE SPECIFIC TO CRYSTAL SPECIFIED
X1
C2
XTAL
Function
SDRAM A10 Pin. Enables applications to refresh an SDRAM in parallel with a host access.
Crystal Oscillator Terminal. Used in conjunction with CLKIN to enable the ADSP-21065L’s
internal clock generator or to disable it to use an external clock source. See CLKIN.
PWM Output/Event Capture. In PWMOUT mode, is an output pin and functions as a timer
counter. In WIDTH_CNT mode, is an input pin and functions as a pulse counter/event capture.
Power Supply; nominally +3.3 V dc. (33 pins)
Power Supply Return. (37 pins)
Do Not Connect. Reserved pins that must be left open and unconnected. (7 pins)
R
C2
S
XTAL
C3
L1
–10–
TARGET BOARD CONNECTOR FOR EZ-ICE PROBE
The ADSP-2106x EZ-ICE emulator uses the IEEE 1149.1
JTAG test access port of the ADSP-2106x to monitor and con-
trol the target board processor during emulation. The EZ-ICE
probe requires the ADSP-2106x’s CLKIN, TMS, TCK, TRST,
TDI, TDO, EMU and GND signals be made accessible on the
target system via a 14-pin connector (a 2 row x 7 pin strip header)
such as that shown in Figure 6. The EZ-ICE probe plugs directly
onto this connector for chip-on-board emulation. You must add
this connector to your target board design if you, intend to use
the ADSP-2106x EZ-ICE.
The total trace length between the EZ-ICE connector and the
furthest device sharing the EZ-ICE JTAG pins should be lim-
ited to 15 inches maximum for guaranteed operation. This
restriction on length must include EZ-ICE JTAG signals, which
are routed to one or more 2106x devices or to a combination of
2106xs and other JTAG devices on the chain.
The 14-pin, 2-row pin strip header is keyed at the Pin 3 loca-
tion—you must remove Pin 3 from the header. The pins must
be 0.025 inch square and at least 0.20 inch in length. Pin spac-
ing should be 0.1 ¥ 0.1 inches. Pin strip headers are available
from vendors such as 3M, McKenzie and Samtec.
Figure 6. Target Board Connector for ADSP-2106x EZ-ICE
(JTAG Header)
KEY (NO PIN)
BTRST
BTMS
BTCK
GND
BTDI
GND
13
11
1
3
5
7
9
TOP VIEW
9
10
12
14
4
2
6
8
EMU
CLKIN (OPTIONAL)
TMS
TCK
TRST
TDI
TDO
REV. C