KSZ8842-32MVLI Micrel Inc, KSZ8842-32MVLI Datasheet - Page 48

• Manufacturer Part Number: KSZ8842-32MVLI
• Description: 2-Port Ethernet Switch/Repeater + Generic (32-bit) Bus Interface( )
• Manufacturer: Micrel Inc

Specifications of KSZ8842-32MVLI

• Controller Type: Ethernet Switch Controller
• Interface: PCI
• Voltage - Supply: 3.1 V ~ 3.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 128-LQFP
• Number Of Primary Switch Ports: 2
• Internal Memory Buffer Size: 32
• Operating Supply Voltage (typ): 3.3V
• Fiber Support: Yes
• Integrated Led Drivers: Yes
• Phy/transceiver Interface: MII
• Power Supply Type: Analog/Digital
• Data Rate (typ): 10/100Mbps
• Vlan Support: Yes
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Pin Count: 128
• Mounting: Surface Mount
• Jtag Support: No
• Operating Supply Voltage (max): 3.5V
• Operating Supply Voltage (min): 3.1V
• Operating Temperature Classification: Industrial
• Data Rate: 100Mbps
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: 576-1635 - BOARD EVALUATION KSZ8842-16MVL
• Current - Supply: -
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant
• Other names: 576-3270

For egress rate limiting, the Leaky Bucket algorithm is applied to each output priority queue for shaping output traffic. Inter
frame gap is stretched on a per frame base to generate smooth, non-burst egress traffic. The throughput of each output
priority queue is limited by the egress rate specified.
If any egress queue receives more traffic than the specified egress rate throughput, packets may be accumulated in the
output queue and packet memory. After the memory of the queue or the port is used up, packet dropping or flow control
will be triggered. As a result of congestion, the actual egress rate may be dominated by flow control/dropping at the
ingress end, and may be therefore slightly less than the specified egress rate.
To reduce congestion, it is a good practice to make sure the egress bandwidth exceeds the ingress bandwidth.
MAC Filtering Function
Use the static table to assign a dedicated MAC address to a specific port. When a unicast MAC address is not recorded in
the static table, it is also not learned in the dynamic MAC table. The KSZ8842M includes an option that can filter or
forward unicast packets for an unknown MAC address. This option is enabled by SGCR7[7].
The unicast MAC address filtering function is useful in preventing the broadcast of unicast packets that could degrade the
quality of this port in applications such as voice over Internet Protocol (VoIP).
Configuration Interface
The KSZ8842M operates only as a managed switch.
EEPROM Interface
It is optional in the KSZ8842M to use an external EEPROM. In the case that an EEPROM is not used, the EEEN pin must
be tied Low or floating.
The external serial EEPROM with a standard microwire bus interface is used for non-volatile storage of information such
as the host MAC address, base address, and default configuration settings. The KSZ8842M can detect if the EEPROM is
a 1KB (93C46) or 4KB (93C66) EEPROM device (the 93C46 and the 93C66 are typical EEPROM devices). The
EEPROM is organized as 16-bit mode.
If the EEEN pin is pulled high, the KSZ8842M performs an automatic read of the external EEPROM words 0H to 6H after
the de-assertion of Reset. The EEPROM values are placed in certain host-accessible registers. EEPROM read/write
functions can also be performed by software read/writes to the EEPCR registers.
The KSZ8842M EEPROM format is given below.
Micrel, Inc.
October 2007
WORD
0H
1H
2H
3H
4H
5H
6H
7H-3FH
15
Base Address
Host MAC Address Byte 2
Host MAC Address Byte 4
Host MAC Address Byte 6
Reserved
Reserved
ConfigParam (see Table 13)
Not used for KSZ8842M (available for user to use)
Table 12. EEPROM Format
48
8
7
Host MAC Address Byte 1
Host MAC Address Byte 3
Host MAC Address Byte 5
KSZ8842-16/32 MQL/MVL/MVLI/MBL
0
M9999-102207-1.9