XPSAC3421P SQUARE D, XPSAC3421P Datasheet - Page 78

• Manufacturer Part Number: XPSAC3421P
• Description: SAFETY RELAY 300V 2.5A PREVENTA
• Manufacturer: SQUARE D

Specifications of XPSAC3421P

• Contact Current Max: 60mA
• Contact Voltage Ac Nom: 115V
• Contact Configuration: 3NO
• Relay Mounting: DIN Rail
• External Height: 66mm
• External Width: 114mm
• External Depth: 22.5mm
• Rohs Compliant: Yes

Description
8
7
6
5
4
1
2
2
3
Safety automation system solutions
Preventa™ safety PLCs
Compact and modular
Safety remote input modules XPSMF1
On the front cover of the metal enclosure:
1
2
3
4
5
6
7
8
Inputs 1…16 Orange On
Outputs 1…4 Orange On
24 VDC
RUN
ERROR
PROG
FORCE
FAULT
OSL
BL
RJ45
(1) Removable screw terminals are provided with safety input module XPSMF1DI1601.
Description
Safety remote input module XPSMF1DI1601
Status LED details
Safety remote input module XPSMF1DI1601
LED
One terminal block
Four terminal blocks
LEDs per terminal block).
One terminal block
output status LEDs.
Two RJ45 (type 10BASE-T/100BASE-TX) integrated switched ports, for
connection on Ethernet network and for configuring IP address.
Eight process status LEDs.
One ground connection screw.
On the top: one “Reset” button.
On the rear face: one spring operated mounting device for mounting on 35
mm 5 rail.
Red
Orange On
Orange On
Orange On
Orange Flashing
Orange Flashing
Green
Yellow
Color
Green
Green
Status
On
Off
On
Flashing
Off
On
Off
Flashing
Off
Flashing
Off
Flashing
Off
On
Flashing
Off
On
Flashing
(1)
(1)
(1)
for c 24 V supply.
for connection of digital line control outputs, with four digital
for connection of digital inputs, with input status LED (four
Error display for line control.
The user application has caused an error.
The system configuration is defective.
The loading of a new operating system was defective and
the operating system is corrupt.
An error has occurred while writing to FLASH ROM memory
(during updating of the operating system).
One or more I/O errors have occurred.
None of the above errors have occurred.
Emergency loading of the operating system is active.
COM in INIT_Fail state.
Full duplex mode operation.
Signal collision.
Half duplex mode operation, no collision.
Connection established.
Interface active.
Meaning
Inputs active.
Outputs active.
c 24 V voltage present.
No voltage.
Normal service mode, loaded program running, the PLC
receives I/O messages, communication and hardware/
software tests carried out.
The CPU is in STOP and is not executing any user
application. All the outputs are reset to a safe, de-energized
state.
The CPU is in “ERROR” state (see ERROR).
Software error or hardware anomaly detected by the CPU.
The monitoring program (Watchdog) has triggered the
STOP state of the process because the programmed cycle
time has been exceeded.
The CPU has stopped the execution of the user application,
ended all hardware and software tests and all outputs have
been reset.
The process can only be started again from the PC.
No errors detected.
The CPU is being loaded with a new configuration.
The FLASH ROM is being loaded with a new operating
system.
No loading of configuration or operating system.
The CPU is in RUN mode and force is active.
The system is not processing (STOP), but force is prepared
and is activated if the dual processor is started.
Force mode not activated.
2/77
10
10
1
1
2
2
3
3
4
4
5
5
6
6
7
7
8
8
9
9