D10BFPQ BANNER ENGINEERING, D10BFPQ Datasheet - Page 7

• Manufacturer Part Number: D10BFPQ
• Description: D10BFPQ QD 6 PIN PICO RED
• Manufacturer: BANNER ENGINEERING
• Type: Fiber Opticr

Specifications of D10BFPQ

• Brand/series: D10 Expert™
• Current, Switching: 150 mA
• Function: Fiber Optic
• Ip Rating: IP50
• Mounting Type: Bracket
• Output: NPN/PNP
• Primary Type: Photoelectric
• Sensing Mode: Selectable
• Technology: Photoelectric
• Termination: 6-Wire Connector
• Voltage, Supply: 30 VDC
• Accessories Available: Cordsets and Plastic Fiber Optic Cable

Figure 6.
(no signal)
(no signal)
Darkest
Darkest
T
the presented condition
threshold 6.25% above
Banner Engineering Corp. • Minneapolis, MN U.S.A
Sensor positions
Output OFF
T
T T T
T
Operate shown)
Single-Point Dark SET (Light
0.8 seconds
> 2 seconds
•
• Present sensing condition
•
0.04 seconds ≤ “Click” ≤ 0.8 seconds
Press and hold Static push
Five-click Static push button
button > 2 seconds
Presented
Condition
Threshold position
Manual Adjust
adjusted by
Push Button
T
T
T T T
0.8 seconds
> 2 seconds
Condition
Presented
or
T
or
Output ON
T
T
T
T
T
Most Light
Most Light
(saturated
(saturated
T
T
T
signal)
signal)
T
T
T
T
T
T
T
T
T
T
T
•
•
•
T
T
T
T
T
T
Single-pulse remote line
Present sensing condition
Five-pulse remote line
0.04 seconds ≤ T ≤ 0.8 seconds
T
T
T
T
T
T
T
T
•
•
• Threshold position is adjustable using the “+” and “-” buttons (Manual Adjust).
•
A single sensing condition is presented, and the sensor positions a threshold 6.25%
above the taught condition. When a condition lighter than the threshold is sensed, the
output either turns ON or OFF, depending on the Light/Dark Operate setting (see SETUP
mode, page 8).
Dark SET and Light/Dark Operate Selection
In Light Operate mode, Dark SET teaches the Output OFF condition. In Dark Operate
mode, Dark SET teaches the Output ON condition.
T
T
T
T
T
T
T
T
dark background with varying lighter targets.
Sets a threshold 6.25% above the taught condition.
Any condition lighter than the threshold condition causes the output to change state.
Recommended for applications where only one condition is known, for example a stable
T
T
T
T
T
T
Remote Line
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
1x
2x
3x
4x
5x
6x
7x
T
T
T
T
T
T
T
T
T
T
T
T
T
1x
2x
3x
4x
5x
6x
7x
Sensor returns to RUN mode with new settings
Power LED: OFF
Output LED:
Static LEDs:
Threshold Condition Accepted
Power LED: ON
Output LED:
Bargraph:
Threshold Condition Unacceptable
Power LED: ON
Output LED:
Bargraph:
Sensor returns to “SET Sensing Condition.”
Single-Point Dark SET
4 indicators flash
#1, 3, 5, 7 flash to show
together
failure
ON (push button)
LO & DO alternately
ON (push button)
OFF (remote line)
ON (push button)
flashing
OFF (remote line)
OFF (remote line)
Result
P/N 117830 rev. E
or
or
or
7