611073-000 Tyco Electronics, 611073-000 Datasheet - Page 625

• Manufacturer Part Number: 611073-000
• Description: Connector Accessories Adapter Aluminum Alloy Olive Drab Cadmium Over Electroless Nickel
• Manufacturer: Tyco Electronics
• Type: Adapterr

Catalog 1654025
Revised 12-04
www.tycoelectronics.com
Dimensions are in millimeters
and inches unless otherwise
specified. Values in brackets
are U.S. equivalents.
Supporting Information
Glossary
Milking Off
Action that occurs when the
inner layer (the encapsulant
or adhesive) of the tubing or
molded part acts as a lubri-
cant, allowing the tubing to
slip off the substrate
(because the tubing wants
to recover to a smaller
diameter).
Minimum Full Recovery
Temperature
See Recovery Temperature.
MO (Manufacturing Order)
A series of operation-work-
order cards identifying
materials to be used and
the type and quantity of
products to be manufac-
tured. An MO is controlled
and issued by Production
Control to the manufactur-
ing operation.
MOD Code (Material
Modification Code)
A code designating a par-
ticular stage in the produc-
tion process. Most MOD
codes describe the way the
product is packaged.
MS (Manufacturing
Specification)
A set of process instruc-
tions used in the manufac-
turing of tubing products.
Customer Logistics,
Product Management, or
Manufacturing Engineering
initiate the MS;
Manufacturing Engineering
controls it. The product
design and quality parame-
ters are provided to
Manufacturing Engineering
by Product Development
and Quality Assurance.
Successful trial runs of a
new product or design
usually precede the initia-
tion of an MS (see SMO).
A proprietary Raychem
document, an MS is not
available to customers.
Multiconductor
More than one component
within a single-cable
complex.
(Continued)
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
Multiple-Conductor Cable
A combination of two or
more components cabled
together.
Nick
A small cut or notch in con-
ductor strands or insulation.
Nominal
A descriptor applied to a
dimension representing the
center of the range of toler-
ance or a value if no toler-
ance is applied.
OFT (Optional Flame Test)
Canadian Standards
Association’s test for flame-
retardance. Tubing with an
OFT rating is highly flame-
retardant.
Ohm
The unit of electrical
resistance.
Operating Temperature
The maximum internal tem-
perature at which a system,
harness, or connector may
operate in continuous ser-
vice; generally expressed
as a time and temperature.
Operating Temperature Range
The range between the
maximum and the minimum
internal temperature of insu-
lation in a system, harness,
or connector in continuous
service. The lower limit is
determined by low-temper-
ature flex test.
Optional Flame Test
See OFT.
Packaging
The process of physically
locating, connecting, and
protecting devices or com-
ponents.
Panel
The side or front (usually
metal) of a piece of equip-
ment on which connectors
are mounted.
Panel-mount
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-5-729-0425
Method of fixing one-half of
a connector to a board,
panel, or frame. Usually, the
female half of the connector
is the mounted portion and
the male half is the remov-
able portion.
PC (Production Control)
Group responsible for
directing and regulating the
movement of goods through
the entire manufacturing
cycle, from the requisition-
ing of raw materials to the
delivery of the finished
products.
PCN
See RPN.
Peripheral Seal
A seal provided around the
periphery of connector
inserts to prevent the
ingress of fluids or contami-
nants at the perimeter of
mated connectors.
Permittivity
See Dielectric Constant.
Pick
The number of crossovers
of braiding units per inch
of cable.
Pigtail
A short conductor or wire
extending from an electrical
or electronic device to
serve as a jumper or ground
connection.
Pin Contact
An electrical terminal,
usually in a connector.
Normally a smaller termina-
tion than a lug.
Plastic Deformation
Change in dimensions
under a load that does not
recover when the load is
removed.
Plasticizer
A softener or lubricant
added to a compound to
make it easier to process
or more flexible in use.
Plating
South America: 55-11-3611-1514
Japan: 81-44-900-5102
Singapore: 65-4866-151
UK: 44-1793-528171
11-13
1 1