PIC24FJ32GA102-E/SS Microchip Technology, PIC24FJ32GA102-E/SS Datasheet - Page 61

• Manufacturer Part Number: PIC24FJ32GA102-E/SS
• Description: 16-bit, 16 MIPS, 32KB Flash, 8KB RAM, Nanowatt XLP 28 SSOP .209in TUBE
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 24Fr

Specifications of PIC24FJ32GA102-E/SS

• Processor Series: PIC24
• Core: PIC24F
• Data Bus Width: 16 bit
• Program Memory Type: Flash
• Program Memory Size: 32 KB
• Data Ram Size: 8192 B
• Interface Type: I2C, SPI, UART
• Maximum Clock Frequency: 32 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 5
• Operating Supply Voltage: 2 V to 3.6 V
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Package / Case: SSOP-28
• Development Tools By Supplier: MPLAB Integrated Development Environment
• Minimum Operating Temperature: - 40 C
• Operating Temperature Range: - 40 C to + 125 C
• Supply Current (max): 300 mA
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 32MHz
• Connectivity: I²C, IrDA, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LVD, POR, PWM, WDT
• Number Of I /o: 21
• Eeprom Size: -
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 2 V ~ 3.6 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Lead Free Status / Rohs Status: Details

REGISTER 6-1:
TABLE 6-1:
6.1
If clock switching is enabled, the system clock source at
device Reset is chosen as shown in Table 6-2. If clock
switching is disabled, the system clock source is always
selected according to the oscillator Configuration bits.
Refer to Section 8.0 “Oscillator Configuration” for
further details.
TABLE 6-2:
 2010 Microchip Technology Inc.
bit 1
bit 0
Note 1:
TRAPR (RCON<15>)
IOPUWR (RCON<14>)
CM (RCON<9>)
EXTR (RCON<7>)
SWR (RCON<6>)
WDTO (RCON<4>)
SLEEP (RCON<3>)
IDLE (RCON<2>)
BOR (RCON<1>)
POR (RCON<0>)
DPSLP (RCON<10>)
Note:
Reset Type
WDTO
MCLR
SWR
POR
BOR
2:
Clock Source Selection at Reset
All Reset flag bits may be set or cleared by the user software.
Flag Bit
All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
BOR: Brown-out Reset Flag bit
1 = A Brown-out Reset has occurred. Note that BOR is also set after a Power-on Reset.
0 = A Brown-out Reset has not occurred
POR: Power-on Reset Flag bit
1 = A Power-on Reset has occurred
0 = A Power-on Reset has not occurred
FNOSC Configuration bits
(CW2<10:8>)
COSC Control bits
(OSCCON<14:12>)
RESET FLAG BIT OPERATION
OSCILLATOR SELECTION vs.
TYPE OF RESET (CLOCK
SWITCHING ENABLED)
Clock Source Determinant
RCON: RESET CONTROL REGISTER
Trap Conflict Event
Illegal Opcode or Uninitialized W Register Access
Configuration Mismatch Reset
MCLR Reset
RESET Instruction
WDT Time-out
PWRSAV #SLEEP Instruction
PWRSAV #IDLE Instruction
POR, BOR
POR
PWRSAV #SLEEP instruction with DSCON <DSEN> set
PIC24FJ64GA104 FAMILY
Setting Event
6.2
The Reset times for various types of device Reset are
summarized in Table 6-3. Note that the System Reset
signal, SYSRST, is released after the POR and PWRT
delay times expire.
The time at which the device actually begins to execute
code will also depend on the system oscillator delays,
which include the Oscillator Start-up Timer (OST) and
the PLL lock time. The OST and PLL lock times occur
in parallel with the applicable SYSRST delay times.
The FSCM delay determines the time at which the
FSCM begins to monitor the system clock source after
the SYSRST signal is released.
(1)
(CONTINUED)
Device Reset Times
PWRSAV Instruction, POR
Clearing Event
DS39951C-page 61
POR
POR
POR
POR
POR
POR
POR
POR
—
—