MT8LSDT1664HY-13EG3 Micron Technology Inc, MT8LSDT1664HY-13EG3 Datasheet
MT8LSDT1664HY-13EG3
Specifications of MT8LSDT1664HY-13EG3
Related parts for MT8LSDT1664HY-13EG3
MT8LSDT1664HY-13EG3 Summary of contents
Page 1
... SMALL-OUTLINE SDRAM MODULE Features • PC100- and PC133-compliant, 144-pin, small- outline, dual in-line memory module (SODIMM) • Utilizes 125 MHz and 133 MHz SDRAM components • Unbuffered • 64MB (8 Meg x 64), 128MB (16 Meg x 64), and 256MB (32 Meg x 64) • Single +3.3V power supply • ...
Page 2
... The designators for component and PCB revision are the last two characters of each part number. Consult factory for current revision codes. Example: MT8LSDT1664HG-133B1 09005aef8077d63a SD8C8_16_32x64HG.fm - Rev. C 6/04 EN 64MB, 128MB, 256MB (x64, DR) 144-PIN SDRAM SODIMM MODULE DENSITY CONFIGURA-TION 64MB 8 Meg x 64 64MB 8 Meg x 64 ...
Page 3
... A2 69 S0# 105 S1# 107 SS NOTE: 1. Pin Connect for 64MB and128MB modules, or A12 for 256MB module. Figure 2: Pin Locations (144-Pin SODIMM) Front View U2 U3 PIN 1 (all odd pins) 09005aef8077d63a SD8C8_16_32x64HG.fm - Rev. C 6/04 EN 64MB, 128MB, 256MB (x64, DR) Table 5: PIN SYMBOL PIN SYMBOL PIN SYMBOL PIN SYMBOL ...
Page 4
... Not Connected: These pins should be left unconnected. DNU – Do Not Use: These pins are not connected on these modules, but are assigned pins on other modules in this product family. 4 144-PIN SDRAM SODIMM Micron Technology, Inc., reserves the right to change products or specifications without notice. ...
Page 5
... WE# A0-A11 (64MB/128MB) A0-A12 (256MB) BA0-1 NOTE: 1. All resistor values are 10 unless otherwise specified. 2. Per industry standard, Micron modules use various component speed grades as referenced in the module part numbering guide at: www.micron.com/support/numbering.html. 09005aef8077d63a SD8C8_16_32x64HG.fm - Rev. C 6/04 EN 64MB, 128MB, 256MB (x64, DR) Figure 3: Functional Block Diagram ...
Page 6
... EEPROM device (DIMM) occur via a standard I using the DIMM’s SCL (clock) and SDA (data) signals. Write protect (WP) is tied to ground on the module, permanently disabling hardware write protect. Initialization SDRAM devices must be powered up and initialized in a predefined manner ...
Page 7
... The ordering of accesses within a burst is deter- mined by the burst length, the burst type and the start- ing column address, as shown in Table 7, Burst Definition Table, on page 8. Figure 4: Mode Register Definition 64MB Module and Reserved* WB *Should program M11 and M10 = “0, 0” to ensure compatibility with future devices ...
Page 8
... For a burst length of one, A0–Ai select the unique col- umn to be accessed, and mode register bit M3 is ignored for 64MB modules for 128MB and 256MB modules 09005aef8077d63a SD8C8_16_32x64HG.fm - Rev. C 6/04 EN 64MB, 128MB, 256MB (x64, DR) Figure 5: CAS Latency Diagram ...
Page 9
Test modes and reserved states should not be used, because unknown operation or incompatibility with future versions may result. Write Burst Mode When the burst length programmed via M0- M2 applies to both READ and WRITE bursts; ...
Page 10
Commands The Truth Table provides a quick reference of avail- able commands. This is followed by written descrip- tion of each command. For a more detailed des- Table 9: Truth Table – SDRAM Commands and DQMB Operation CKE is HIGH ...
Page 11
... NOTE: a. Value calculated as one module rank in this operating condition, and all other module ranks in power-down mode. b. Value calculated reflects all module ranks in this operating condition. 09005aef8077d63a SD8C8_16_32x64HG.fm - Rev. C 6/04 EN 64MB, 128MB, 256MB (x64, DR) tional sections of this specification is not implied ...
Page 12
... NOTE: a. Value calculated as one module bank in this operating condition, and all other module banks in power-down mode. b. Value calculated reflects all module banks in this operating condition. 09005aef8077d63a SD8C8_16_32x64HG.fm - Rev. C 6/04 EN 64MB, 128MB, 256MB (x64, DR) ...
Page 13
... Input Capacitance: CK, CKE, S# Input Capacitance: DQMB Inuput/Output Capacitnance: DQ Table 15: Electrical Characteristics and Recommended AC Operating Conditions Notes 11, 31; notes appear on page 15 Module AC timing parameters comply with PC100 and PC133 Design Specs, based on component parameters AC CHARACTERISTICS PARAMETER Access time from CLK (positive edge) ...
Page 14
Table 16: AC Functional Characteristics Notes 11, 31; notes appear on page 15 PARAMETER READ/WRITE command to READ/WRITE command CKE to clock disable or power-down entry mode CKE to clock enable or power-down exit setup ...
Page 15
... RAS used in -13E speed grade mod- t ule SPDs is calculated from RC - possible through the module pin, not what each memory device contributes. Micron Technology, Inc., reserves the right to change products or specifications without notice. ©2004 Micron Technology, Inc. All rights reserved. t RP; clock( ...
Page 16
SPD Clock and Data Conventions Data states on the SDA line can change only during SCL LOW. SDA state changes during SCL HIGH are reserved for indicating start and stop conditions (Fig- ure 6, Data Validity, and Figure 7, Definition ...
Page 17
Table 17: EEPROM Device Select code The most significant bit (b7) is sent first Memory Area Select Code (two arrays) Protection Register Select Code Table 18: EEPROM Operating modes MODE RW BIT Current Address Read Random Address Read Sequential Read ...
Page 18
Table 19: Serial Presence-Detect EEPROM DC Operating Conditions All voltages referenced DDSPD PARAMETER/CONDITION SUPPLY VOLTAGE INPUT HIGH VOLTAGE: Logic 1; All inputs INPUT LOW VOLTAGE: Logic 0; All inputs OUTPUT LOW VOLTAGE 3mA ...
Page 19
... Total Number of SPD Memory Bytes 2 Memory Type 3 Number of Row Addresses 4 Number of Column Addresses 5 Number of Module Ranks 6 Module Data Width 7 Module Data Width (Continued) 8 Module Voltage Interface Levels t 9 SDRAM Cycle Time, CK (CAS Latency = SDRAM Access from CLK, AC (CAS Latency = 3) 11 Module Configuration Type 12 Refresh Rate/Type 13 ...
Page 20
... Week of Manufacture in BCD 95-98 Module Serial Number 99-125 Manufacturer-specific Data (RSVD) 126 System Frequency 127 SDRAM Component & Clock Detail NOTE The value of RAS used for -13E modules is calculated from 09005aef8077d63a SD8C8_16_32x64HG.fm - Rev. C 6/04 EN 64MB, 128MB, 256MB (x64, DR) ENTRY (VERSION) 32MB, 64MB, or 128MB ...
Page 21
R (2X) U2 0.071 (1.80) (2X) 0.236 (6.00) 0.100 (2.55) 0.079 (2.00) PIN 1 0.13 (3.30) U9 PIN 144 NOTE: All dimensions in inches (millimeters); Data Sheet Designation Released (No Mark): This data sheet contains mini- mum and ...