BTS716GXT Infineon Technologies, BTS716GXT Datasheet
BTS716GXT
Specifications of BTS716GXT
Related parts for BTS716GXT
BTS716GXT Summary of contents
Page 1
... Data Sheet Smart High-Side Power Switch Ω Ω Ω Block Diagram 1 BTS716G Package P-DSO-20 PG-DSO20 V1.0, 2007-05-13 ...
Page 2
... IN4 Data Sheet control and protection circuit of channel 2 control and protection circuit of channel 3 control and protection circuit of channel 4 2 Smart High-Side Power Switch BTS716G V1.0, 2007-05-13 ...
Page 3
... OUT3 13 OUT4 4 ST1/2 Diagnostic feedback 1/2,3/4 of channel 1,2,3,4 8 ST3/4 open drain, low on failure 2 GND1/2 Ground of chip 1 (channel 1,2) 6 GND3/4 Ground of chip 2 (channel 3,4) Data Sheet Smart High-Side Power Switch Pin configuration (top view GND1/2 2 IN1 3 ST1/2 4 IN2 5 GND3/4 6 IN3 7 ST3/4 8 IN4 9 ...
Page 4
... Load dump protection 1 V LoadDump = 2 Ω 400 ms low or high each channel loaded with R Operating temperature range Storage temperature range Power dissipation (DC) 4) (all channels active) Maximal switchable inductance, single pulse = 12V 150°C j,start mJ, 0 Ω 2 182 mJ, 0 Ω 3 460 mJ, 0 Ω ...
Page 5
... Electrical Characteristics Parameter and Conditions -40...+150° unless otherwise specified j bb Load Switching Capabilities and Characteristics On-state resistance ( OUT); each channel, two parallel channels, T four parallel channels, T see diagram, page 11 Nominal load current two parallel channels active: four parallel channels active 85° ...
Page 6
... V ON(CL OUT , Thermal overload trip temperature Thermal hysteresis 10) is the voltage, where the device doesn´t change it´s switching condition for 15ms after the supply voltage falling below the lower limit of Vbb(on) ) not subject to production test, specified by design 11 ) Supply voltages higher than V 12 resistor for the GND connection is recommended) ...
Page 7
... Data Sheet Symbol each of the four channels - > out ∆ V 19) t d(STon) 19) t d(STon) t d(SToff) 19) t d(SToff 0 IN(off IN(on +1.6 mA +1.6 mA Smart High-Side Power Switch Values min typ -- -- bb -- 600 ON 1.7 2.8 OUT(OL) 1 2.5 4 IN(T+) 1.0 -- IN(T-) -- 0.2 IN( 5.4 -- ST(high ST(low) V1.0, 2007-05-13 ...
Page 8
... H = "High" Level Status signal valid after the time delay shown in the timing diagrams Parallel switching of channel 1 and 2 (also channel 3 and 4) is easily possible by connecting the inputs and outputs in parallel (see truth table). If switching channel parallel, the status outputs ST1/2 and ST3/4 have to be configured as a 'Wired OR' function with a single pull-up resistor ...
Page 9
... Open-load detection, OFF-state diagnostic condition: Open Load OUT < 375 Ω ST(ON) GND disconnect Any kind of load. In case high is V Due to V > GND 9 Smart High-Side Power Switch BTS716G = 150 Ω typ., R GND Z2 OUT1...4 > typ.; IN low ≈ OUT IN IN(T+) = low signal available. ...
Page 10
... For inductive load currents up to the limits defined by Z (max. ratings and diagram on page 10) each switch is protected against loss Consider at your PCB layout that in the case of Vbb dis- connection with energized inductive load all the load current flows through the GND connection ...
Page 11
... Typ. on-state resistance high L R [mOhm] ON Typ. standby current , I 9...34 V, IN1,2,3,4 = low EE RII [µA] bb(off) Data Sheet Smart High-Side Power Switch V [ [° BTS716G V1.0, 2007-05-13 ...
Page 12
... Timing diagrams All channels are symmetric and consequently the diagrams are valid for channel 1 to channel 4 Figure 1a: V turn on: bb Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data Sheet Figure 2b: Switching a lamp: Figure 3a: Turn on into short circuit: shut down by overtemperature, restart by cooling ...
Page 13
... Figure 3b: Turn on into short circuit: shut down by overtemperature, restart by cooling (two parallel switched channels 1 and 2) ST1 and ST2 have to be configured as a 'Wired OR' function ST1/2 with a single pull-up resistor. Figure 4a: Overtemperature: Reset if T < Data Sheet Smart High-Side Power Switch Figure 5a: Open load: detection in OFF-state, turn on/off to open load Open load of channel 1 ...
Page 14
... You can find all of our packages, sorts of packing and others in our Infineon Internet Page “Products”: http://www.infineon.com/products. Data Sheet 2) 0.1 0.2 24x 12.8 -0.2 17 Smart High-Side Power Switch 0.35 x 45˚ 1) 7.6 -0.2 +0.8 0.4 ±0.3 10.3 GPS05094 Dimensions in mm V1.0, 2007-05-13 BTS716G ...
Page 15
... Revision History Version Date Changes 1.0 2007-05-13 Creation of the green datasheet. Data Sheet Smart High-Side Power Switch 18 BTS716G V1.0, 2007-05-13 ...
Page 16
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...