DS3234S# Maxim Integrated Products, DS3234S# Datasheet - Page 8

• Manufacturer Part Number: DS3234S#
• Description: IC RTC W/TCXO 20-SOIC
• Manufacturer: Maxim Integrated Products
• Type: Clock/Calendar/TCXO/Crystalr

Specifications of DS3234S#

• Memory Size: 2K (256 x 8)
• Time Format: HH:MM:SS (12/24 hr)
• Date Format: YY-MM-DD-dd
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 20-SOIC (7.5mm Width)
• Function: Clock/Calendar/Alarm/Battery Backup/Interrupt
• Rtc Memory Size: 256 Byte
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2 V
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Rtc Bus Interface: Serial (4-Wire, SPI)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Extremely Accurate SPI Bus RTC with
Integrated Crystal and SRAM
8
2, 7–14
18, 20
PIN
15
16
17
19
1
3
4
5
6
_____________________________________________________________________
INT/SQW
NAME
32kHz
DOUT
SCLK
GND
V
N.C.
V
RST
DIN
CS
BAT
CC
Active-Low Chip Select Input. Used to select or deselect the device.
No Connection. Not connected internally. Must be connected to ground.
32kHz Push-Pull Output. If disabled with either EN32kHz = 0 or BB32kHz = 0, the state of the 32kHz pin will be
low.
DC Power Pin for Primary Power Supply. This pin should be decoupled using a 0.1µF to 1.0µF capacitor.
Active-Low Interrupt or Square-Wave Output. This open-drain pin requires an external pullup resistor. It can be
left open if not used. This multifunction pin is determined by the state of the INTCN bit in the Control Register
(0Eh). When INTCN is set to logic 0, this pin outputs a square wave and its frequency is determined by RS2
and RS1 bits. When INTCN is set to logic 1, then a match between the timekeeping registers and either of the
alarm registers activates the INT/SQW pin (if the alarm is enabled). Because the INTCN bit is set to logic 1
when power is first applied, the pin defaults to an interrupt output with alarms disabled. The pullup voltage can
be up to 5.5V, regardless of the voltage on V
Active-Low Reset. This pin is an open-drain input/output. It indicates the status of V
V
pin is driven high impedance. The active-low, open-drain output is combined with a debounced pushbutton
input function. This pin can be activated by a pushbutton reset request. It has an internal 50k_ nominal value
pullup resistor to V
oscillator is disabled, t
Ground
Backup Power-Supply Input. If V
pin and the battery can cause improper operation. UL recognized to ensure against reverse charging when
used with a lithium battery. Go to
SPI Data Input. Used to shift address and data into the device.
SPI Clock Input. Used to control timing of data into and out of the device. Either clock polarity can be used. The
clock polarity is determined by the device based on the state of SCLK when CS goes low. Pins 18 and 20 are
electrically connected together internally.
SPI Data Output. Data is output on this pin when the device is in read mode; CMOS push-pull driver.
PF
specification. As V
CC
. No external pullup resistors should be connected. On first power-up, or if the crystal
RST
CC
falls below V
is bypassed and RST immediately goes high.
BAT
www.maxim-ic.com/qa/info/ul
is not used, connect to ground. Diodes placed in series between the V
PF
, the RST pin is driven low. When V
CC
. If not used, this pin can be left unconnected.
FUNCTION
.
CC
exceeds V
CC
Pin Description
relative to the
PF
, for t
RST
, the RST
BAT