MAX148BCAP+ Maxim Integrated Products, MAX148BCAP+ Datasheet - Page 21

• Manufacturer Part Number: MAX148BCAP+
• Description: IC ADC SRL 8CH 10BIT LP 20-SSOP
• Manufacturer: Maxim Integrated Products

Specifications of MAX148BCAP+

• Number Of Bits: 10
• Sampling Rate (per Second): 133k
• Data Interface: MICROWIRE™, QSPI™, Serial, SPI™
• Number Of Converters: 1
• Power Dissipation (max): 640mW
• Voltage Supply Source: Single Supply
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 20-SSOP
• Number Of Adc Inputs: 8
• Architecture: SAR
• Conversion Rate: 133 KSPs
• Resolution: 10 bit
• Input Type: Voltage
• Interface Type: 4-Wire (SPI, QSPI, MICROWIRE, TMS320)
• Voltage Reference: Internal 2.5 V or External
• Supply Voltage (max): 5 V
• Maximum Power Dissipation: 640 mW
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

The MAX148/MAX149 can interface with QSPI using the
circuit in Figure 20 (f
0). This QSPI circuit can be programmed to do a conver-
sion on each of the eight channels. The result is stored
in memory without taxing the CPU, since QSPI incorpo-
rates its own microsequencer.
The MAX148/MAX149 are QSPI compatible up to the
maximum external clock frequency of 2MHz.
Figure 21 shows an application circuit to interface the
MAX148/MAX149 to the TMS320 in external clock mode.
The timing diagram for this interface circuit is shown in
Figure 22.
Use the following steps to initiate a conversion in the
MAX148/MAX149 and to read the results:
Figure 22. TMS320 Serial-Interface Timing Diagram
1) The TMS320 should be configured with CLKX (trans-
High-Speed Digital Interfacing with QSPI
mit clock) as an active-high output clock and CLKR
(TMS320 receive clock) as an active-high input
clock. CLKX and CLKR on the TMS320 are tied
together with the MAX148/MAX149’s SCLK input.
SSTRB
DOUT
SCLK
DIN
CS
______________________________________________________________________________________
START
+2.7V to +5.25V, Low-Power, 8-Channel,
SCLK
SEL2
= 2.0MHz, CPOL = 0, CPHA =
TMS320LC3x Interface
SEL1
SEL0
UNI/BIP
SGL/DIF
PD1
2) The MAX148/MAX149’s CS pin is driven low by the
3) An 8-bit word (1XXXXX11) should be written to the
4) The MAX148/MAX149’s SSTRB output is monitored
5) The TMS320 reads in one data bit on each of the
6) Pull CS high to disable the MAX148/MAX149 until
PD0
TMS320’s XF_ I/O port to enable data to be clocked
into the MAX148/MAX149’s DIN.
MAX148/MAX149 to initiate a conversion and place
the device into external clock mode. See Table 1 to
select the proper XXXXX bit values for your specific
application.
through the TMS320’s FSR input. A falling edge on
the SSTRB output indicates that the conversion is in
progress and data is ready to be received from the
MAX148/MAX149.
next 16 rising edges of SCLK. These data bits rep-
resent the 10 + 2-bit conversion result followed by 4
trailing bits, which should be ignored.
the next conversion is initiated.
Serial 10-Bit ADCs
MSB
B8
S1
S0
HIGH
IMPEDANCE
HIGH
IMPEDANCE
21