DAC101S101CIMK/NOPB National Semiconductor, DAC101S101CIMK/NOPB Datasheet - Page 5

• Manufacturer Part Number: DAC101S101CIMK/NOPB
• Description: IC CONV D-A 10BIT R-R TSOT-23-6
• Manufacturer: National Semiconductor
• Series: PowerWise®r

Specifications of DAC101S101CIMK/NOPB

• Settling Time: 5µs
• Number Of Bits: 10
• Data Interface: Parallel
• Number Of Converters: 1
• Voltage Supply Source: Single Supply
• Power Dissipation (max): 1.41mW
• Operating Temperature: -40°C ~ 105°C
• Mounting Type: Surface Mount
• Package / Case: TSOT-23-6, TSOT-6
• Number Of Channels: 1
• Resolution: 10b
• Interface Type: Serial (3-Wire, SPI, QSPI, Microwire)
• Single Supply Voltage (typ): 3.3/5V
• Dual Supply Voltage (typ): Not RequiredV
• Architecture: Resistor-String
• Power Supply Requirement: Single
• Output Type: Voltage
• Integral Nonlinearity Error: ±2.8LSB
• Single Supply Voltage (min): 2.7V
• Single Supply Voltage (max): 5.5V
• Dual Supply Voltage (min): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Operating Temp Range: -40C to 105C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 6
• Package Type: TSOT
• For Use With: DAC101S101EVAL - BOARD EVALUATION DAC101S101
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DAC101S101CIMK; DAC101S101CIMKTR

f
t
SR
t
1/f
t
t
t
t
t
t
t
SCLK
s
WU
H
L
SUCL
SUD
DHD
CS
SYNC
Symbol
A.C. and Timing Characteristics
The following specifications apply for V
range 12 to 1011. Boldface limits apply for T
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed
specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test
conditions.
Note 2: All voltages are measured with respect to GND = 0V, unless otherwise specified
Note 3: When the input voltage at any pin exceeds the power supplies (that is, less than GND, or greater than V
mA. The 20 mA maximum package input current rating limits the number of pins that can safely exceed the power supplies with an input current of 10 mA to two.
Note 4: The absolute maximum junction temperature (T
junction-to-ambient thermal resistance (θ
for maximum power dissipation will be reached only when the device is operated in a severe fault condition (e.g., when input or output pins are driven beyond
the power supply voltages, or the power supply polarity is reversed). Obviously, such conditions should always be avoided.
Note 5: Human body model is 100 pF capacitor discharged through a 1.5 kΩ resistor. Machine model is 220 pF discharged through ZERO Ohms.
Note 6: See the section entitled "Surface Mount" found in any post 1986 National Semiconductor Linear Data Book for methods of soldering surface mount
devices.
Note 7: The analog inputs are protected as shown below. Input voltage magnitudes up to V
However, errors in the conversion result can occur if any input goes above V
−100mV
Note 8: To guarantee accuracy, it is required that V
Note 9: Typical figures are at T
Level).
Note 10: This parameter is guaranteed by design and/or characterization and is not tested in production.
SCLK
≤
SCLK Frequency
Output Voltage Settling Time
(Note
Output Slew Rate
Glitch Impulse
Digital Feedthrough
Wake-Up Time
SCLK Cycle Time
SCLK High time
SCLK Low Time
Set-up Time SYNC to SCLK Rising
Edge
Data Set-Up Time
Data Hold Time
SCLK fall to rise of SYNC
SYNC High Time
input voltages
10)
≤
Parameter
2.8V
J
= 25°C, and represent most likely parametric norms. Test limits are guaranteed to National's AOQL (Average Outgoing Quality
DC
to ensure accurate conversions.
JA
), and the ambient temperature (T
A
= +2.7V to +5.5V, R
A
be well bypassed.
J
max) for this device is 150°C. The maximum allowable power dissipation is dictated by T
MIN
100h to 300h code
change, R
Code change from 200h to 1FFh
V
V
V
V
2.7
3.6
A
A
A
A
≤
= 5V
= 3V
= 5V
= 3V
≤
≤
T
A
V
V
A
A
≤
≤
≤
T
L
MAX
3.6
5.5
= 2kΩ
Conductions
L
A
A
= 2kΩ to GND, C
), and can be calculated using the formula P
: all other limits T
or below GND by more than 100 mV. For example, if V
5
C
A
20154104
L
+ 300 mV or to 300 mV below GND will not damage this device.
≤
200 pF
L
A
= 200 pF to GND, f
= 25°C, unless otherwise specified.
A
Typical
), the current at that pin should be limited to 10
−15
0.5
2.5
2.5
12
39
−2
5
1
6
5
5
0
9
5
D
MAX = (T
SCLK
= 30 MHz, input code
Limits
J
max − T
7.5
4.5
30
33
13
13
20
10
A
0
5
3
1
is 2.7V
A
) / θ
DC
, ensure that
www.national.com
JA
J
MHz (max)
max, the
µs (max)
. The values
(Limits)
ns (min)
ns (min)
ns (min)
ns (min)
ns (min)
ns (min)
ns (min)
ns (min)
ns (min)
ns (min)
nV-sec
nV-sec
Units
V/µs
µs
µs