SC1200UCL-266 AMD (ADVANCED MICRO DEVICES), SC1200UCL-266 Datasheet - Page 218

• Manufacturer Part Number: SC1200UCL-266
• Manufacturer: AMD (ADVANCED MICRO DEVICES)

Specifications of SC1200UCL-266

• Lead Free Status / Rohs Status: Not Compliant

218
Index BBh
Index BCh
Note:
Index BDh-BFh
Index C0h-C3h
Index C4h-C7h
Index C8h-CBh
Table 6-29. F0: PCI Header/Bridge Configuration Registers for GPIO and LPC Support (Continued)
31:0
31:0
31:0
Bit
7:0
7:4
3:1
0
This register configures the Core Logic module to support a 3V Suspend mode. Setting bit 0 causes the SUSP_3V signal to
assert after the appropriate conditions, stopping the system clocks. A delay of 0-15 msec is programmable (bits [7:4]) to allow
for a delay for the clock chip and CPU PLL to stabilize when an event Resumes the system.
A write to the CPU Suspend Command register (F0 Index AEh) with bit 0 written as:
0: Internal SUSP#/SUSPA# handshake occurs. The GX1 module is put into a low-power state, and the system clocks are not
stopped. When a break/resume event occurs, it releases the CPU halt condition.
1: Internal SUSP#/SUSPA# handshake occurs and the SUSP_3V signal is asserted, thus invoking a full system Suspend (both
GX1 module and system clocks are stopped). When a break event occurs, the SUSP_3V signal is de-asserted, the PLL delay
programmed in bits [7:4] are invoked which allows the clock chip and GX1 module PLL to stabilize before de-asserting the
internal SUSP# signal.
Description
RTC Index Shadow. The RTC Shadow register contains the last written value of the RTC Index register (I/O Port 070h).
PLL Delay. The programmed value in this field sets the delay (in milliseconds) after a break event occurs before the internal
SUSP# signal is de-asserted to the GX1 module. This delay is designed to allow the clock chip and CPU PLL to stabilize
before starting execution. This delay is only invoked if the STP_CLK bit was set.
The 4-bit field allows values from 0 to 15 msec.
0000: 0 msec
0001: 1 msec
0010: 2 msec
0011: 3 msec
Reserved. Set to 0.
CPU Clock Stop.
0: Normal internal SUSP#/SUSPA# handshake.
1: Full system Suspend.
User Defined Device 1 Base Address. This 32-bit register supports power management (Trap and Idle timer resources) for
a PCMCIA slot or some other device in the system. The value in this register is used as the address comparator for the
device trap/timer logic. The device can be memory or I/O mapped (configured in F0 Index CCh).
The Core Logic module cannot snoop addresses on the Fast-PCI bus unless it actually claims the cycle. Therefore, Traps
and Idle timers cannot support power management of devices on the Fast-PCI bus.
User Defined Device 2 Base Address. This 32-bit register supports power management (Trap and Idle timer resources) for
a PCMCIA slot or some other device in the system. The value in this register is used as the address comparator for the
device trap/timer logic. The device can be memory or I/O mapped (configured in F0 Index CDh).
The Core Logic module cannot snoop addresses on the Fast-PCI bus unless it actually claims the cycle. Therefore, Traps
and Idle timers cannot support power management of devices on the Fast-PCI bus.
User Defined Device 3 Base Address. This 32-bit register supports power management (Trap and Idle timer resources) for
a PCMCIA slot or some other device in the system. The value in this register is used as the address comparator for the
device trap/timer logic. The device can be memory or I/O mapped (configured in F0 Index CEh).
The Core Logic module cannot snoop addresses on the Fast-PCI bus unless the it actually claims the cycle. Therefore,
Traps and Idle timers cannot support power management of devices on the Fast-PCI bus.
32579B
User Defined Device 1 Base Address Register (R/W)
User Defined Device 2 Base Address Register (R/W)
User Defined Device 3 Base Address Register (R/W)
0100: 4 msec
0101: 5 msec
0110: 6 msec
0111: 7 msec
Clock Stop Control Register (R/W)
RTC Index Shadow Register (RO)
Reserved
Core Logic Module - Bridge, GPIO, and LPC Registers - Function 0
1000: 8 msec
1001: 9 msec
1010: 10 msec
1011: 11 msec
AMD Geode™ SC1200/SC1201 Processor Data Book
1100: 12 msec
1101: 13 msec
1110: 14 msec
1111: 15 msec
Reset Value: 00000000h
Reset Value: 00000000h
Reset Value: 00000000h
Reset Value: xxh
Reset Value: 00h
Reset Value: 00h