IDT79RV4650-150DP IDT, Integrated Device Technology Inc, IDT79RV4650-150DP Datasheet - Page 3

• Manufacturer Part Number: IDT79RV4650-150DP
• Description: IC MPU 64BIT W/DSP 150MHZ 208QFP
• Manufacturer: IDT, Integrated Device Technology Inc

Specifications of IDT79RV4650-150DP

• Processor Type: RISC 64-Bit
• Speed: 150MHz
• Voltage: 3.3V
• Mounting Type: Surface Mount
• Package / Case: 208-QFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -
• Other names: 79RV4650-150DP

Integer Execution Engine
and is upwardly compatible with applications that run on the earlier
generation parts. The RC4650 includes the same additions to the
instruction set found in the RC4700 family of microprocessors, targeted
at improving performance and capability while maintaining binary
compatibility with earlier RC3000 processors.
support, improved performance for commonly used code sequences in
operating system kernels, and faster execution of floating-point intensive
applications. All resource dependencies are made transparent to the
programmer, insuring transportability among implementations of the
MIPS instruction set architecture. In addition, MIPS-III specifies new
instructions defined to take advantage of the 64-bit architecture of the
processor.
are considered extensions to the MIPS-III architecture. These instruc-
tions improve the multiply and multiply-add throughput of the CPU,
making it well suited to a wide variety of imaging and DSP applications.
These extensions, which use opcodes allocated by MIPS Technologies
for this purpose, are supported by a wide variety of development tools.
single cycle ALU operations (logical, shift, add, sub) and autonomous
multiply/divide unit. The 64-bit register resources include: 32 general-
purpose orthogonal integer registers, the HI/LO result registers for the
integer multiply/divide unit, and the program counter. In addition, the on-
chip floating-point co-processor adds 32 floating-point registers, and a
floating-point control/status register.
Register File
registers are used for scalar integer operations and address calculation.
The register file consists of two read ports and one write port and is fully
bypassed to minimize operation latency in the pipeline. Figure 1 illus-
trates the RC4650 Register File.
ALU
adder performs address calculations in addition to arithmetic operations,
and the logic unit performs all logical and shift operations. Each of these
units is highly optimized and can perform an operation in a single pipe-
line cycle.
Integer Multiply/Divide
for high-speed multiply and multiply-accumulate operation. Table 1
shows the performance, expressed in terms of pipeline clocks, achieved
by the RC4650 integer multiply unit.
IDT79RC4650™
The RC4650 implements the MIPS-III Instruction Set Architecture
The extensions result in better code density, greater multi-processing
Finally, the RC4650 also implements additional instructions, which
The MIPS integer unit implements a load/store architecture with
The RC4650 has thirty-two general-purpose 64-bit registers. These
The RC4650 ALU consists of the integer adder and logic unit. The
The RC4650 uses a dedicated integer multiply/divide unit, optimized
3 of 25
divide operation are placed in the HI and LO registers. The values can
then be transferred to the general purpose register file using the MFHI/
MFLO instructions.
specify that the multiply results bypass the “Lo” register and are placed
immediately in the primary register file. By avoiding the explicit “Move-
from-Lo” instruction required when using “Lo”, throughput of multiply-
intensive operations is increased.
“multiply-add” operation, MAD, used to perform multiply-accumulate
operations. This instruction multiplies two numbers and adds the product
to the current contents of the HI and LO registers. This operation is used
in numerous DSP algorithms, and allows the RC4650 to cost reduce
systems requiring a mix of DSP and control functions.
these operations along with pipelining to allow new operations to be
issued before a previous one has fully completed. Table 1 also shows
the repeat rate (peak issue rate), latency, and number of processor stalls
required for the various operations. The RC4650 performs automatic
operand size detection to determine the size of the operand, and imple-
ments hardware interlocks to prevent overrun, allowing this high-perfor-
mance to be achieved with simple programming.
Floating-Point Co-Processor
processor on chip, including a floating-point register file and execution
units. The floating-point co-processor forms a “seamless” interface with
the integer unit, decoding and executing instructions in parallel with the
integer unit.
floating-point operations. This enables the RC4650 to perform functions
such as graphics rendering, without requiring extensive die are or power
consumption.
tions found in the RC64475. However, to maintain software compatibility,
MULT/U, MAD/U
MUL
DMULT,
DMULTU
DIV, DIVU
DDIV, DDIVU
The MIPS-III architecture defines that the results of a multiply or
The RC4650 adds a new multiply instruction, “MUL”, which can
An additional enhancement offered by the RC4650 is an atomic
Finally, aggressive implementation techniques feature low latency for
The RC4650 incorporates an entire single-precision floating-point co-
The RC4650’s floating-point unit directly implements single-precision
The RC4650 does not directly implement the double-precision opera-
Opcode
Table 1 RC4650 Integer Multiply Operation
16 bit
32 bit
16 bit
32 bit
any
any
any
Operand
Size
3
4
3
4
6
36
68
Latency Repeat
2
3
2
3
5
36
68
April 10, 2001
0
0
1
2
0
0
0
Stall