MPC8313EVRAFFB Freescale Semiconductor, MPC8313EVRAFFB Datasheet - Page 39

• Manufacturer Part Number: MPC8313EVRAFFB
• Description: IC MPU POWERQUICC II PRO 516PBGA
• Manufacturer: Freescale Semiconductor

Specifications of MPC8313EVRAFFB

• Processor Type: MPC83xx PowerQUICC II Pro 32-Bit
• Speed: 333MHz
• Voltage: 0.95 V ~ 1.05 V
• Mounting Type: Surface Mount
• Package / Case: 516-PBGA
• Processor Series: MPC8xxx
• Core: e300
• Data Bus Width: 32 bit
• Development Tools By Supplier: MPC8313E-RDB
• Maximum Clock Frequency: 400 MHz
• Operating Supply Voltage: - 0.3 V to + 1.26 V
• Maximum Operating Temperature: + 105 C
• Mounting Style: SMD/SMT
• Data Ram Size: 16 KB
• I/o Voltage: 2.5 V
• Interface Type: I2C, SPI, UART
• Minimum Operating Temperature: - 40 C
• Program Memory Type: EEPROM/Flash
• For Use With: MPC8313E-RDB - BOARD PROCESSOR
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

9.2.2
The DC level requirement for the MPC8313E SerDes reference clock inputs is different depending on the
signaling mode used to connect the clock driver chip and SerDes reference clock inputs as described
below.
Freescale Semiconductor
•
•
Differential mode
— The input amplitude of the differential clock must be between 400 and 1600 mV differential
— For external DC-coupled connection, as described in
— For external AC-coupled connection, there is no common mode voltage requirement for the
Single-ended mode
— The reference clock can also be single-ended. The SD_REF_CLK input amplitude
— The SD_REF_CLK input average voltage must be between 200 and 400 mV.
— To meet the input amplitude requirement, the reference clock inputs might need to be DC or
peak-to-peak (or between 200 and 800 mV differential peak). In other words, each signal wire
of the differential pair must have a single-ended swing less than 800 mV and greater than
200 mV. This requirement is the same for both external DC-coupled or AC-coupled
connection.
Receiver Characteristics,”
average voltage (common mode voltage) to be between 100 and 400 mV.
SerDes reference clock input requirement for the DC-coupled connection scheme.
clock driver. Since the external AC-coupling capacitor blocks the DC level, the clock driver
and the SerDes reference clock receiver operate in different command mode voltages. The
SerDes reference clock receiver in this connection scheme has its common mode voltage set to
XCOREV
the command mode voltage (XCOREV
requirement for AC-coupled connection scheme.
(single-ended swing) must be between 400 and 800 mV peak-to-peak (from V
SD_REF_CLK either left unconnected or tied to ground.
the SerDes reference clock input requirement for the single-ended signaling mode.
AC coupled externally. For the best noise performance, the reference of the clock could be DC
DC Level Requirement for SerDes Reference Clocks
MPC8313E PowerQUICC
SS
. Each signal wire of the differential inputs is allowed to swing below and above
Figure 23. Receiver of SerDes Reference Clocks
SD n _REF_CLK
SD n _REF_CLK
the maximum average current requirements sets the requirement for
™
II Pro Processor Hardware Specifications, Rev. 3
SS
50 Ω
50 Ω
).
Figure 25
Input
Amp
Section 9.2.1, “SerDes Reference Clock
shows the SerDes reference clock input
High-Speed Serial Interfaces (HSSI)
Figure 24
min
Figure 26
to V
shows the
max
shows
) with
39