EMC6D103S-CZC SMSC, EMC6D103S-CZC Datasheet - Page 42

no-image

EMC6D103S-CZC

Manufacturer Part Number
EMC6D103S-CZC
Description
Industrial Temperature Sensors Auto Fan Contrllr Up to 4 Fans
Manufacturer
SMSC
Datasheet

Specifications of EMC6D103S-CZC

Lead Free Status / Rohs Status
Lead free / RoHS Compliant
Revision 0.3 (03-01-07)
7.1.4.4
7.1.4.4.1
7.1.4.4.2
and the Tach Reading register will be set to either FFFEh or FFFFh depending on the state of the Slow
Tach bits located in the TACHx Options registers at offsets 90h - 93h. Software can easily compute
the RPM value using the tachometer reading value if it knows the number of edges per revolution.
Mode 2 – Monitor Tach input When PWM is ‘ON’
In this mode, the PWM is used to pulse the Fan motor of a 3-wire fan. 3-wire fans use the same
power supply to drive the fan motor and to drive the tachometer output logic. When the PWM is ‘ON’
the fan generates valid tach pulses. When the PWM is not driving the Fan, the tachometer signal is
not generated and the tach signal becomes indeterminate or tristate. Therefore, Mode 2 only makes
tachometer measurements when the associated PWM is driving high during an update cycle. As a
result, the Fan tachometer measurement is “synchronized” to the PWM output, such that it only looks
for tach pulses when the PWM is ‘ON’.
Note: High frequency PWM operation is designed for use with four wire fans. Although some three
Note: Any fan tachometer input may be associated with any PWM output (see
During an update cycle, if an insufficient number of tachometer pulses are detected during this time
period, the PWM output is “stretched” (held high) until either the programmed number of edges is
detected or the maximum stretch time expires, whichever comes first. (See
Modes 1 & 2 on page
PWM STRETCHING
PWM stretching will be done by the hardware each update of the tachometer registers (every 300ms,
500ms, or 1000ms). The PWM will be stretched until the programmed number of edges is detected or
until the programmed max PWM stretching time-out occurs. If at least one edge but less than the
programmed number of edges is detected, the fan is considered slow. If no edge is detected, the fan
is considered stopped.
Note: The interrupt status bits are set, if enabled, to indicate that a slow or stopped fan event has
The PWM maximum stretching times (50, 100, 200, 400, 600, 800, 950 msec) represent the maximum
time that the PWM will be ‘on’. So if the hardware needs to stretch the PWM ‘on’ time then it will be
stretched beyond the PWM duty cycle ‘on’ time up to the programmed PWM stretch time.
If PWM stretching is disabled, the tachometer will only be monitored during the PWM duty cycle ‘ON’
time. The hardware will never stretch the PWM ‘ON’ time. The hardware treats the disabled case as
Stretch Time equals PWM ‘ON’ time. Interrupts are reported in the same manner as if stretching is
enabled.
Note: When stretching is enabled, the hardware will continue the edge detection until the required
ASSUMPTIONS (REFER TO FIGURE 7.5, "PWM AND TACHOMETER CONCEPT"):
The Tachometer pulse generates 5 transitions per fan revolution (i.e., two fan tachometer periods per
revolution, edges 2 → 6). One half of a revolution (one tachometer period) is equivalent to three edges
(2 → 4 or 3 → 5). One quarter of a revolution (one-half tachometer period) is equivalent to two edges.
To obtain the fan speed, count the number of 90Khz pulses that occurs between 2 edges i.e., 2 → 3,
between 3 edges i.e., 2 → 4, or between 5 edges, i.e. 2 → 6 (the case of 9 edges is not shown). The
time from 1-2 occurs through the guard time and is not to be used. For the discussion below, an edge
is a high-to-low or low-to-high transition (edges are numbered – refer to Figure 7.5, "PWM and
Tachometer Concept").
wire fans are capable of operating with high frequency PWM, the tach output is very difficult to
read. External circuitry is required for accurate tach reading of a three wire fan that is driven
with high frequency PWM.
Tachometers to PWMs on page
occurred when the tach reading registers are greater than the tach limit registers.
number of edges occur or the stretching time period expires.
Fan Control Device with High Frequency PWM Support and Hardware Monitoring Features
44)
DATASHEET
47.)
42
Summary of Operation for
SMSC EMC6D103
Linking Fan
Datasheet

Related parts for EMC6D103S-CZC