DP83936AVUL-20 National Semiconductor, DP83936AVUL-20 Datasheet - Page 96

• Manufacturer Part Number: DP83936AVUL-20
• Description: IC CTRLR ORIENT NETWORK 160PQFP
• Manufacturer: National Semiconductor

Specifications of DP83936AVUL-20

• Controller Type: Network Interface Controller (NIC)
• Interface: Twisted Pair
• Voltage - Supply: 4.75 V ~ 5.25 V
• Current - Supply: 140mA
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 160-MQFP, 160-PQFP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Other names: *DP83936AVUL-20

http
Number
T56
T60
T63
T64
T69
T69a
T70a
T71a
T75b
T77
T77a
T77b
T78
T79a
T81
T83
T84
T85a
9 0 AC and DC Specifications
REGISTER WRITE BMODE
Note 1 This figure shows a slave access to the SONIC-T when the SONIC-T is idle or rather not in master mode If the SONIC-T is a bus master there will be
some differences as noted in the Memory Arbitration Slave Access diagram The BSCK states (T1 T2 etc ) are the equivalent processor states during a slave
access
Note 2 bcyc
Note 3 It is not necessary to meet the setup time for CS and SAS (T56 and T69) since these signals are asynchronously sampled Meeting the setup time for these
signals however makes it possible to use T60 to determine when SMACK will be asserted SAS may be asserted anytime before the next falling edge of the clock
that the CS is sampled on (as shown by specification T69) For multiple register accesses CS can be held low and SAS can be used to delimit the slave cycle
(T69a must be met in order to terminate and start another cycle) In this case SMACK will be asserted as soon as T69 timing is met
Note 4 T60 could range from 1 bus clock minimum to 5 bus clock maximum depending on what state machine the SONIC-T is in when the CS signal is asserted
This timing is not tested but is guaranteed by design This specification assumes that both T56 is met for CS and T69 is met for SAS T60 specification also
assumes that there were no wait states in the current master mode access (if CS is asserted when SONIC-T is in Master Mode) If there were wait states then it
would increase the T60 futher
Note 5 It is not necessary to meet the setup time for SAS (T69a) since this signal is asynchronously sampled Meeting the setup time for this signal however will
ensure DSACK0 1 becomes TRI-STATE (77b) and SMACK goes high (T79) at the falling edge of T1 Both CS and SAS could cause DSACK0 1 to deassert but only
SAS could cause DSACK0 1 to become TRI-STATE
www national com
e
CS Asynchronous Setup to BSCK (Notes 3 4)
CS Valid to SMACK Low (Notes 2 3 4)
Register Address Setup to SAS
Register Address Hold from SAS
SAS Asynchronous Setup to BSCK (Notes 3 4)
SAS Asynchronous Setup to BSCK (Notes 3 5)
SRW (Write) Setup to SAS
SRW (Write) Hold from SAS
BSCK to DSACK0 1 Low
CS to DSACK0 1 High (Note 5)
SAS to DSACK0 1 High (Note 5)
BSCK to DSACK0 1 TRI-STATE (Note 5)
Skew between DSACK0 1
BSCK to SMACK High (Note 5)
BSCK to SMACK Low
Register Write Data Setup to BSCK
Register Write Data Hold from BSCK
Minimum CS Deassert Time (Notes 2 3)
bus clock cycle time (T3)
e
Parameter
1 (Note 1)
(Continued)
96
Min
14
8
1
6
8
7
5
4
8
8
1
20 MHz
Max
22
22
20
31
19
19
5
3
Min
12
7
1
5
7
6
4
3
7
7
1
25 MHz
Max
20
18
29
17
17
20
5
3
Min
10
6
1
4
6
5
3
2
6
6
1
33 MHz
TL F 12597 – 75
Max
18
16
27
15
15
18
2
Units
bcyc
bcyc
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns