MCP2021-500E/MD Microchip Technology, MCP2021-500E/MD Datasheet - Page 10

• Manufacturer Part Number: MCP2021-500E/MD
• Description: IC LIN TXRX ON-BOARD VREG 8DFN
• Manufacturer: Microchip Technology
• Type: Transceiverr

Specifications of MCP2021-500E/MD

• Number Of Drivers/receivers: 1/1
• Protocol: LIN
• Voltage - Supply: 6 V ~ 18 V
• Mounting Type: Surface Mount
• Package / Case: 8-DFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: APGRD004 - REF DESIGN MOD AUTO AMBNT LIGHTAC164130 - BOARD DAUGHT PICTL PLUS ECAN/LIN
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

MCP2021/2
1.6
1.6.1
The MCP2021 has a low-drop-out voltage, positive
regulator capable of supplying 5.00 V
50 mA of load current over the entire operating
temperature range of -40°C to +125°C. With a load
current of 50 mA, the minimum input to output voltage
differential required for the output to remain in
regulation is typically +0.5V (+1V maximum over the
full operating temperature range). Quiescent current is
less than 100 µA with a full 50 mA load current when
the input to output voltage differential is greater than
+3.00V.
The regulator requires an external output bypass
capacitor for stability. See
ity and ESR for stable operation.
Designed for automotive applications, the regulator will
protect itself from double-battery jumps and up to +43V
load dump transients. The voltage regulator has both
short-circuit and thermal shutdown protection built-in.
Regarding the correlation between V
please refer to
voltage (V
provide stable regulation, the output Vreg will track the
input down to approximately 3.5V, at which point the
regulator will turn off. This will allow microcontrollers
with internal POR circuits to generate a clean arming of
the Power-on Reset trip point. The MCP2021 will then
monitor V
6.0V.
FIGURE 1-4:
DS22018E-page 10
Internal Voltage Regulator
BB
V
BB
REG
5.0V REGULATOR
) drops below the differential needed to
and turn on the regulator when Vbb is
Figure 1-5
VOLTAGE REGULATOR BLOCK DIAGRAM
Figure 2-3
through 1-7. When the input
Sampling
Network
V
BB
REF
for correct capac-
DC
, V
±3% at up to
REG
and I
DD
,
Transient
Element
Pass
Fast
Loop
When the input voltage (V
differential needed to provide stable regulation, the
output V
+4.25V. The regulator will turn off the output at this
point. This will allow PIC
internal POR circuits, to generate a clean arming of the
Power-on Reset trip point. The regulator output will
stay off until V
In the start phase, the device must see at least 6.0V to
initiate operation during power up. In the Power-down
mode, the V
The regulator has a thermal shutdown. If the thermal
protection
condition, and the signals T
T
from the thermal shutdown is equal to adequate cooling
time.
XD
Note:
is HIGH, the regulator will shut down. The recovery
Buffer
REG
The regulator has an overload current
limiting of approximately 100 mA. During a
short circuit, the V
V
off. After a recovery time of about three
milliseconds, the V
again. If there is no short circuit, (V
3.5V) then the V
on.
) will track the input down to approximately
BB
circuit
REG
BB
monitor will be turned off.
is above +5.75 V
is lower than 3.5V, the V
detects
© 2009 Microchip Technology Inc.
REG
XD
®
an
BB
and RXD are LOW, or
REG
microcontrollers, with
REG
will be switched back
) drops below the
DC
over
.
will be checked
is monitored. If
V
V
SS
BB
REG
temperature
will turn
REG
>