INT-1532-L-5-L-010 TE Connectivity, INT-1532-L-5-L-010 Datasheet - Page 47

• Manufacturer Part Number: INT-1532-L-5-L-010
• Description: DIGITAL PANEL METER, 4-DIGIT, 57.7V TO 139V / 100V TO 240V
• Manufacturer: TE Connectivity

Specifications of INT-1532-L-5-L-010

• No. Of Digits / Alpha: 4
• Meter Function: Digital
• Meter Range: 0mA To 20mA
• Digit Height: 96mm
• Supply Voltage Range: 57.7V To 139V / 100V To 240V
• Power Consumption: 3W
• Rohs Compliant: NA

Features
Remote metering
Remote status information
PC configuration of programmable
parameters
Full access to each and every
parameter
Upload and download Integra
settings
View and edit Integra settings
Load and save parameter settings
Print data logs
Password protected
Models Supported
Integra 1530
Integra 1560/1580
Applications
PC based communication systems
SCADA Systems
PLC interfacing
Energy management systems
46
Minimum Recommended System Requirements
Product Code
INT-SOFT Communication and Configuration
Software
Password Security
Access to Integra programmable parameters is password protected, however, settings
and the electrical measurements can be viewed without entering the password. The
access passwords entered on the PC must be identical to those stored inside the Integra.
Operation
INT-SOFT is designed to provide two basic functions: to display and configure the
parameters of an Integra unit, and to monitor the measured values of the selected
Integra. INT-SOFT is extremely simple to operate, featuring user-friendly navigation
toolbars and drop-down menus.
INT- SOFT is a simple Windows-style user interface enabling remote
monitoring and configuration of Integra parameters, outputs, digital
communications, pulsed relays, current and power demand. INT-SOFT can
be installed on any PC running Windows 95, NT or 2000. INT-SOFT allows
the user to load and save configurations to a PC hard disk and to send and
retrieve settings directly from the Integra. Settings can also be copied
between individual Integra units.
Up to 31 Integra units can be connected to a PC COM port via an
RS485/RS232 converter, however, INT-SOFT can only communicate with
one Integra at a time.
Status information of measured parameters is usually communicated into a
building management system, but can also be monitored through the
configuration software. The software queries the selected Integra every
few seconds to obtain data which can be viewed on a dedicated
measurements page.
INT-SOFT
Processor:
Operating systems:
RAM:
Monitor:
Hard Disc:
CD-ROM drive:
RS232 port:
INT-SOFT window
Measurements:
System window:
Password:
Energy and demands:
Analogue outputs:
Digital communications:
Read / write register:
Configuration toolbar
New configuration:
Open configuration file:
Save configuration file:
Print configuration:
Online:
Offline:
Upload configuration:
Download configuration:
Configure PC communications:
486 66MHz
Windows 95, NT or 2000
16Mb
12” SVGA (640 x 480 resolution)
5 Mb free
Required for installation
9-pin D0type connector
Menu
Displays all measurement values
System type, volts, current, max system power,
secondary volts, nominal volts, firmware
version, special product code
Existing password, new password, confirm
password, change password
Demand period, demand interval, reset demands,
pulse rate divisor, pulse width, reset energy.
Set-up of phase readings, output modes,
operating mode, trim controls, output of power
factor parameters
Baud rate, parity, stop bits and unique address
Display and modification of Modbus registers
Description
Create new Integra configuration
Load an existing configuration from a disk file
Save the current configuration to a disk file
Send the current configuration to a printer
Connect to the selected Integra
Disconnect from the selected Integra
Upload the configuration from the selected Integra
Send current configuration to the selected Integra
Enables setting of PC communications
Integra Communication and Configuration Software.