TLE6285G Infineon Technologies, TLE6285G Datasheet
TLE6285G
Specifications of TLE6285G
TLE6285GNT
TLE6285GT
TLE6285GT
Available stocks
Related parts for TLE6285G
TLE6285G Summary of contents
Page 1
TLE 6285 ...
Page 2
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...
Page 3
LIN-Transceiver with Voltage Regulator Features • Single-wire transceiver, suitable for LIN protocol • Transmission rate kBaud • Compatible to LIN specification 1.3, 2.0 • Compatible to ISO 9141 functions • Low current consumption in sleep mode • ...
Page 4
Figure 1 Pin Configuration (top view) Data Sheet ...
Page 5
Table 1 Pin Definitions and Functions Pin No. Symbol Function GND Ground; place to cooling tabs to improve thermal behavior 16 2 INHI Inhibit Voltage Regulator Input; TTL compatible, HIGH active (HIGH switches the VR on); connect ...
Page 6
Functional Block Diagram Output Stage 12 Bus Band-Gap Reference 2 Inhibit INHI Control Figure 2 Block Diagram Data Sheet Driver Temp.- Protection Receiver TLE 4299 Current & ...
Page 7
fte ...
Page 8
In case the voltage regulator control input is not connected to INH output or the microcontroller is active respectively, the TLE 6285 can be set in normal operation mode without a wake-up via the communication bus. LIN Transceiver The LIN ...
Page 9
V very short, the level is not reached and no reset-signal is asserted. This feature LD avoids resets at short negative spikes at the output voltage e.g. caused by load changes. As soon as the output voltage is more positive ...
Page 10
The reset output is an open collector output with a pull-up resistor of typical external pull-up can be added with a resistor value of at least 5 addition the reset switching threshold ...
Page 11
Table 2 Absolute Maximum Ratings Parameter Voltages Supply voltage Battery supply voltage Bus input voltage Bus input voltage Logic voltages at EN, TxD, RxD Input voltages at INHO Output current at INHO Reset output voltage Reset delay voltage V Output ...
Page 12
Table 3 Operating Range Parameter Supply voltage Battery Supply Voltage Junction temperature Thermal Shutdown (junction temperature) Thermal shutdown temp. Thermal shutdown hyst. Thermal Resistances Junction ambient Data Sheet Symbol Limit Values Min. Max. V 4.5 5 ...
Page 13
Table 4 Electrical Characteristics 5V; = 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Current Consumption Current consumption at V (LIN + Voltage Bat Regulator) Current consumption at ...
Page 14
Table 4 Electrical Characteristics (cont’ 5V; = 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Leakage current V V Output (pin ) Q CCO Output voltage Output voltage ...
Page 15
Table 4 Electrical Characteristics (cont’ 5V; = 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Reset Generator (pins RO, RD) Switching threshold Reset pull-up Reset low voltage External ...
Page 16
Table 4 Electrical Characteristics (cont’ 5V; = 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Transmission Input TxD HIGH level input voltage threshold TxD input hysteresis LOW level ...
Page 17
Table 4 Electrical Characteristics (cont’ 5V; = 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Leakage current Bus pull-up resistance Data Sheet 500 ; > ...
Page 18
Table 4 Electrical Characteristics (cont’ 5V; = 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Dynamic Transceiver Characteristics Falling edge slew rate Rising edge slew rate Slope symmetry ...
Page 19
Table 4 Electrical Characteristics (cont’ 5V; = 13.5V respect to ground; positive current flowing into pin; unless otherwise specified. Parameter Delay time for change sleep/stand by mode - normal mode Delay time for ...
Page 20
Diagrams DRL Power-ON Over- Reset temperature Figure 4 Time Response Data Sheet t rr Voltage Drop Under- at Input voltage 20 TLE 6285 t ...
Page 21
Typical Performance Characteristics V ( Output Voltage PIN Input Voltage PIN I BAT Data Sheet V ) versus Output ...
Page 22
I Charge Current versus ch T Temperature j 12 µ 13 - Switching Voltage and dt T Temperature j 3.2 ...
Page 23
V Sense Threshold si T versus Temperature j 1 1.5 Sense Output High 1.4 Sense Output Low 1.3 1.2 1.1 1.0 - Current Consumption I Output Current Q 1 0.8 0.6 ...
Page 24
Application µ ...
Page 25
Package Outlines 1.27 +0.1 0.41 -0.06 Index Marking 1) Does not include plastic or metal protrusion of 0.25 max. per side Figure 6 P-DSO-16-11 (Plastic Dual Small Outline) You can find all of our packages, sorts of packing and others ...