5V49EE703NDGI8 IDT, Integrated Device Technology Inc, 5V49EE703NDGI8 Datasheet

no-image

5V49EE703NDGI8

Manufacturer Part Number
5V49EE703NDGI8
Description
Manufacturer
IDT, Integrated Device Technology Inc
Type
Programmable PLL Clock Synthesizerr
Datasheet

Specifications of 5V49EE703NDGI8

Number Of Elements
4
Pll Input Freq (min)
1MHz
Pll Input Freq (max)
200MHz
Operating Supply Voltage (typ)
3.3V
Operating Temp Range
-40C to 85C
Package Type
VFQFPN EP
Output Frequency Range
0.001 to 200MHz
Operating Supply Voltage (min)
3.135V
Operating Supply Voltage (max)
3.465V
Operating Temperature Classification
Industrial
Pin Count
28
Lead Free Status / Rohs Status
Compliant
EEPROM PROGRAMMABLE CLOCK GENERATOR
Description
The IDT5V49EE703 is a programmable clock generator
intended for high performance data-communications,
telecommunications, consumer, and networking
applications. There are four internal PLLs, each individually
programmable, allowing for four unique non-integer-related
frequencies. The frequencies are generated from a single
reference clock. The reference clock can come from one of
the two redundant clock inputs. A glitchless automatic or
manual switchover function allows any one of the redundant
clocks to be selected during normal operation.
The IDT5V49EE703 is in-system, programmable and can
be programmed through the use of I
internal EEPROM allows the user to save and restore the
configuration of the device without having to reprogram it on
power-up.
Each of the four PLLs has an 7-bit reference divider and a
12-bit feedback divider. This allows the user to generate
four unique non-integer-related frequencies. The PLL loop
bandwidth is programmable to allow the user to tailor the
PLL response to the application. For instance, the user can
tune the PLL parameters to minimize jitter generation or to
maximize jitter attenuation. Spread spectrum generation
and/or fractional divides are allowed on two of the PLLs.
There are a total of five 8-bit output dividers. The outputs
are connected to the PLLs via a switch matrix. The switch
matrix allows the user to route the PLL outputs to any
output bank. This feature can be used to simplify and
optimize the board layout. In addition, each output's slew
rate and enable/disable function is programmable.
IDT® EEPROM PROGRAMMABLE CLOCK GENERATOR
2
C interface. An
1
Features:
Four internal PLLs
Internal non-volatile EEPROM
Fast (400kHz) mode I
Input frequency range: 1 MHz to 200 MHz
Output frequency range: 4.9 kHz to 200 MHz
Reference crystal input with programmable linear load
capacitance
Each PLL has a 7-bit reference divider and a 12-bit
feedback-divider
8-bit output-divider blocks
Fractional division capability on one PLL
Two of the PLLs support spread spectrum generation
capability
I/O Standards:
Programmable slew rate control
Programmable loop bandwidth
Programmable output inversion to reduce bimodal jitter
Redundant clock inputs with glitchless auto and manual
switchover options
Individual output enable/disable
Power-down mode
3.3V core V
Available in TSSOP and VFQFPN packages
-40 to +85 C Industrial Temp operation
– Crystal frequency range: 8 MHz to 50 MHz
– Outputs - 3.3 V LVTTL/ LVCMOS
– Inputs - 3.3 V LVTTL/ LVCMOS
DD
2
C serial interface
IDT5V49EE703
IDT5V49EE703
DATASHEET
REV F 022310

Related parts for 5V49EE703NDGI8

5V49EE703NDGI8 Summary of contents

Page 1

EEPROM PROGRAMMABLE CLOCK GENERATOR Description The IDT5V49EE703 is a programmable clock generator intended for high performance data-communications, telecommunications, consumer, and networking applications. There are four internal PLLs, each individually programmable, allowing for four unique non-integer-related frequencies. The frequencies are generated ...

Page 2

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Functional Block Diagram XIN/REF XOUT CLKIN CLKSEL SD/OE SDA Control Logic SCL SEL[2:0] 1. CLKIN, CLKSEL, SD/OE and SEL[2:0] have pull down resistors. IDT® EEPROM PROGRAMMABLE CLOCK GENERATOR PLL0 (SS) ...

Page 3

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Pin Configuration VDD 1 XOUT 2 XIN/REF 3 VDDx 4 CLKIN 5 GND 6 OUT1 pin VFQFPN (Top View) Pin Descriptions Pin# Pin ...

Page 4

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Pin# Pin Name 16 SCLK 17 CLKSEL 18 AVDD 19 GND 20 OUT6 21 OUT3 22 VDD 23 SEL2 24 SEL1 25 SEL0 26 SD/OE 27 OUT0 28 GND 1. When only an individual single-ended ...

Page 5

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR PLL Features and Descriptions Pre-Divider 1 (D) Values PLL0 1 - 127 PLL1 1 - 127 PLL2 1 - 127 PLL3 3 - 127 1.For PLL0, PLL1 and PLL2, D=0 means PLL power down. For ...

Page 6

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Reference Clock Input Pins and Selection The IDT5V49EE703 supports up to two clock inputs. One of the clock inputs (XIN/ REF) can be driven by either an external crystal or a reference clock. The second ...

Page 7

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR clocks are at different frequencies, the device will always remain on the primary clock unless it is absent for two secondary clock cycles. The secondary clock must always run at a frequency less than or ...

Page 8

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR SS_OFFSET[5:0] These bits are used to program the fractional offset with respect to the nominal M integer value. For center spread, the SS_OFFSET is set to '0' so that the spread spectrum waveform is centered ...

Page 9

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Profile: Waveform starts with SS_OFFSET, SS_OFFSET + SD SS_OFFSET + SD , etc. J+1 Spread Spectrum Using Sinusoidal Profile Example F = 25MHz 100MHz, Fssc = 33KHz with center IN OUT spread of ...

Page 10

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Spread Spectrum Generation (PLL3) PLL3 support spread spectrum generation capability, which users have the option of turning on and off. Spread spectrum profile, frequency, and spread are fully programmable (within limits). The technique is different ...

Page 11

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR PLL Loop Bandwidth: Charge pump gain (Kφ⎞ 2π VCO gain ( 900 MHz/V * 2π VCO M = Total multiplier value (See the Reference Divider, Feedback Divider and Output Divider ...

Page 12

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR SEL[2:0] Function The IDT5V49EE703 can support up to six unique configurations. Users may pre-programmed all these configurations, and select the configurations using SEL[2:0] SEL2 SEL1 SEL0 ...

Page 13

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Each frame starts with a “Start Condition” and ends with an “End Condition”. These are both generated by the Master device. MSB 7-bit slave address R/W 0 – Slave will ...

Page 14

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Progread Note: If the expected read command is not from the next higher register to the previous read or write command, then set a known “read” register address prior to a read operation by issuing ...

Page 15

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Bus DC Characteristics Symbol Parameter V Input HIGH Level IH V Input LOW Level IL V Hysteresis of Inputs HYS I Input Leakage Current IN V Output LOW Voltage ...

Page 16

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Bus AC Characteristics for Fast Mode Symbol Parameter F Serial Clock Frequency (SCL) SCLK t Bus free time between STOP and START BUF t Setup Time, START SU:START t Hold Time, START ...

Page 17

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Absolute Maximum Ratings Stresses above the ratings listed below can cause permanent damage to the IDT5V49EE703. These ratings, which are standard values for IDT commercially rated parts, are stress ratings only. Functional operation of the ...

Page 18

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Capacitance (T = +25 °C) A Symbol C Input Capacitance (CLKIN, CLKSEL, SD/OE, IN SDA, SCL, SEL[2:0]) Pull-down CLKIN, CLKSEL, SD/OE, SEL[2:0] Resistor Crystal Specifications XTAL_FREQ Crystal frequency XTAL_MIN Minimum crystal load capacitance XTAL_MAX Maximum ...

Page 19

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR AC Timing Electrical Characteristics (Spread Spectrum Generation = OFF) Symbol Parameter 1 f Input Frequency Output Frequency f VCO Frequency VCO f PFD Frequency PFD f Loop Bandwidth BW t2 Input ...

Page 20

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Spread Spectrum Generation Specifications Symbol Parameter 1 f Input Frequency Input Frequency Limit IN f Mod Frequency Modulation Frequency MOD f Spread Value Amount of Spread Value (programmable) - Down Spread SPREAD Amount of Spread ...

Page 21

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Programming Registers Table Default Register Addr Hex 7 6 Value 0x00 00 0x01 00 SP OE6 0x02 02 0x03 02 Reserved 0x04 0F SH 0x05 04 Reserved 0x06 00 0x07 00 Reserved 0x08 00 0x09 ...

Page 22

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Default Register Addr Hex 7 6 Value 0x28 00 Reserved 0x29 00 Reserved 0x2A 00 Reserved 0x2B 00 Reserved 0x2C 00 Reserved 0x2D 00 Reserved 0x2E 01 0x2F 01 0x30 01 0x31 01 0x32 01 ...

Page 23

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Default Register Addr Hex 7 6 Value 0x56 00 IP3[3:0]_CFG4 0x57 00 IP3[3:0]_CFG5 0x58 00 IP3[3:0]_CFG0 0x59 00 IP3[3:0]_CFG1 0x5A 00 IP3[3:0]_CFG2 0x5B 00 IP3[3:0]_CFG3 0x5C 03 Reserved 0x5D 03 Reserved 0x5E 03 Reserved 0x5F ...

Page 24

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Default Register Addr Hex 7 6 Value 0x7D 00 0x7E 00 0x7F 00 0x80 00 0x81 00 0x82 00 0x83 00 0x84 00 0x85 00 0x86 00 0x87 00 0x88 FF PM1_CFG0 0x89 FF PM1_CFG1 ...

Page 25

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Default Register Addr Hex 7 6 Value 0xAC 00 TSSC[3:0]_CFG0 0xAD 00 TSSC[3:0]_CFG1 0xAE 00 TSSC[3:0]_CFG2 0xAF 00 TSSC[3:0]_CFG3 0xB0 00 TSSC[3:0]_CFG4 0xB1 00 TSSC[3:0]_CFG5 0xB2 00 DITH_CFG4 X2_CFG4 0xB3 00 DITH_CFG5 X2_CFG5 0xB4 00 ...

Page 26

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Marking Diagram 4703DI #YYWW$ Notes: 1. “#” is the lot number. 2. YYWW is the last two digits of the year and week that the part was assembled. 3. “$” is the assembly mark code. ...

Page 27

... Part / Order Number Marking 5V49EE703NDGI See page 27 5V49EE703NDGI8 See page 27 “G” after the two-letter package code are the Pb-Free configuration and are RoHS compliant. While the information presented herein has been checked for both accuracy and reliability, Integrated Device Technology (IDT) assumes no responsibility for either its use or for the infringement of any patents or other rights of third parties, which would result from its use ...

Page 28

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Revision History Rev. Originator Date Description of Change A R.Willner 4/27/09 Advance Information. B R.Willner 5/04/09 Identified VDDX (crystal oscillator power) and AVDD (analog power) on device. C R.Willner 6/04/09 Add default configurations, pull-down resistor ...

Page 29

IDT5V49EE703 EEPROM PROGRAMMABLE CLOCK GENERATOR Innovate with IDT and accelerate your future networks. Contact: www.IDT.com For Sales 800-345-7015 408-284-8200 Fax: 408-284-2775 Corporate Headquarters Integrated Device Technology, Inc. www.idt.com © 2010 Integrated Device Technology, Inc. All rights reserved. Product specifications subject ...

Related keywords