DPX2MAA106PA106P33B0001FO ITT, DPX2MAA106PA106P33B0001FO Datasheet - Page 20

• Manufacturer Part Number: DPX2MAA106PA106P33B0001FO
• Manufacturer: ITT

Specifications of DPX2MAA106PA106P33B0001FO

• Body Orientation: Straight
• Gender: PIN/PIN
• Termination Style: Crimp
• Total Number Of Contacts: 106/106POS
• Number Of Contact Rows: 8/8
• Housing Material: Aluminum Alloy
• Contact Material: Copper Alloy
• Mounting Style: Panel
• Contact Plating: Gold
• Product Height (mm): 50.8mm
• Product Length (mm): 78.99mm
• Lead Free Status / Rohs Status: Not Compliant

DPX*MA/ME Coaxial Contact Data (for environmental requirements)
ARINC 404
Coaxial Contact Assembly Recommendations
(For Codes A, B, C, D, E, J, K, L and P)
Components/Accessories
NOTE:
RING TYPE RETENTION (A32W2 & A40W1 CONTACT ARRANGEMENTS)
Without Seal (MA)
P-249-1397-001
S-249-1398-003
P-249-1399-001
S-249-1400-003
P-249-1401-001
S-249-1402-003
P-249-1403-001
S-249-1404-003
P-249-1405-001
S-249-1406-003
††For use with connectors supplied less grommet ( Code 29**, etc.)
1. Center contact, rear insulator, crimp ring, support bushing and seal sleeve are packaged separately and
2. Use impact extraction tool no. CET-C4 (038869-0004). An insertion tool is not required. (See Item 4).
3. Cable Assembly Instructions
4. To extract coaxial, push back seal sleeve and support bushing. Then push out coaxial from engaging end
5. When crimping with CA58073 crimp tool, care should be taken to avoid flaring the front end of the
6. To facilitate extraction of contacts and avoid splaying the length of free cable adjacent to the rear
*P for pin, S for socket
†Unsealed accomodates both Seal 1 & Seal 2 Cables.
shipped with the coaxial assembly.
with CET-C4 (038869-0004) impact tool.
crimp ring. Place Crimp jaw so that the second tooth of the indentors is over the end of the crimp ring.
surface of the connector should not be less then 2.000 (50.80).
Step 1- If applicable, determine which portion of seal sleeve should be used. If seal 2 is used, cut off
Step 2 - In sequence, place seal sleeve, support bushing and crimp ring over cable jacket.
Step 3 - Trim cable per illustration.
Step 4 - Place rear insulator over dielectric.
Step 5 - Solder innerconductor to center contact.
Step 6 - Insert soldered cable firmly into coaxial with shielding over coaxial shell.
Step 7 - Pull crimp ring forward until stopped and crimped.
Step 8 - Insert coaxial assembly into connector until engaged. Push support bushing into grommet
The A32W2 & A40W1 (Ring Type Retention); AW8 & A32W4 (LITTLE CAESAR Renention) Coaxial Contact arrangements have been
redesigned to provide ease of insertion/removal of the coaxial contacts. Sealing is accomplished with the addiction of sealing sleeves
provided with the coaxial contact assembly.
Part Number*
seal 1 portion
until shoulder rest on tublular extension. Then pull seal sleeve forward until it is snug
against grommet.
P-249-1397-002
S-249-1398-002
P-249-1399-002
S-249-1400-002
P-249-1401-002
S-249-1402-002
P-249-1403-002
S-249-1404-002
P-249-1405-002
S-249-1406-002
Sealed (ME)
RG179B, RG196
RG179B
RG58B
RG195
Seal 1
Cable Accommodation
X
RG174, RG179B,
RG59B, RG62A
RG180B
RG316
Seal 2
X
X
.158 (4.01)]
.249 (6.32)
.200 (5.08)
.113 (2.87)
.083 (2.11)
Size/Max.
Ins. Dia.
62
.415 (10.54)
.480 (12.19)
.435 (11.05)
.460 (11.68)
.440 (11.18)
.460 (11.68)
.440 (11.18)
.460 (11.68)
.440 (11.18)
.460 (11.68)
'A' Trim
Dim.
CCT-406M
CCT-406M
CA58073
CA58073
CA58073
Crimp
Tool
Specifications and dimensions subject to change
SEAL 1
.420 (10.67)
.400 (10.16)
SEAL 2
(For Codes A, B, C, D, E, J, K, L and P)
DPX*ME Crimp
BUSHING
31
19
SEAL
A2
Dimensions shown in inch (mm)
7
30
6
30
13
24
A32W2 (ME Version)
39
A40W1 (ME Version)
WITHOUT SEAL
12
32W2 (MA Version)
40W1 (MA Version)
18
29
6
5
16
24
Dimensions
12
23
38
Cable Trim
11
20
29
SEALED
17
28
15
5
4
23
www.ittcannon.com
SOCKET
SOCKET
A
22
11
10
19
28
37
27
16
PIN
PIN
4
10
21
36
9
18
27
15
14
3
3
26
BUSHING
22
8
17
26
9
20
35
14
13
25
2
21
2
34
7
25
8
1
1
33
.330 (8.38)
.310 (7.86)
A1
A1
32