DPX2MAA106PA106P33B0001FO ITT, DPX2MAA106PA106P33B0001FO Datasheet - Page 22

• Manufacturer Part Number: DPX2MAA106PA106P33B0001FO
• Manufacturer: ITT

Specifications of DPX2MAA106PA106P33B0001FO

• Body Orientation: Straight
• Gender: PIN/PIN
• Termination Style: Crimp
• Total Number Of Contacts: 106/106POS
• Number Of Contact Rows: 8/8
• Housing Material: Aluminum Alloy
• Contact Material: Copper Alloy
• Mounting Style: Panel
• Contact Plating: Gold
• Product Height (mm): 50.8mm
• Product Length (mm): 78.99mm
• Lead Free Status / Rohs Status: Not Compliant

LITTLE CAESAR Contact Assembly Data
For Codes F, S and T
For Codes G, H and R
For Codes U
For Codes AA
For Codes AC
1. Strip and trim cable as shown on page 60.
2. Solder inner conductor to coaxial contact with crimp ring over braid and rear insulator over inner
3. Insert cable into coaxial with shell under braid. Crimp ring with Cannon crimp tool CA58073.
1. Strip and trim cable as shown on page 60.
2. Solder inner connector to coaxial contact with crimp ring pushed back on cable.
3. Insert cable into coaxial and pull ring forward over braid. Crimp ring with Cannon crimp tool
1. Strip and trim cable as shown on page 60.
2. Slide crimp ring over braid and jacket of cable.
3. Unbraid exposed portion of braid and fold braid wires backward over outside of crimp ring.
4. Insert prepared wire into right angle fitting of shell assembly. Conductor should be aligned in slot of the
5. Solder center conductor of cable to contact. Insert cap and solder in place.
1 . Slip ferrule over cable jacket. Trim outer jacket. Comb out braid as shown. Retrim braid.
2. Bend up combed out braid at right angles to cable. Slide ferrule up to bend and fold braid back against
3. Slide rear insulator over dielectric as shown. Press insulator firmly against folded back braid and trim
4. Place contact over conductor. Press contact and insulator firmly against braid and solder contact to
5. Push cable assembly into shell, pressing against rear of ferrule and crimp area shown with T. & B.
1 . Trim jacket to .680 (17.27)/.660 (16.76) dimension. Then slide ferrule over braid until it stops
2. Fold combed braid over ferrule as shown. Then trim dielectric to .070 (1.78)/.060 (1.52) dimension
3. Press insulator against braid and trim inner conductor to .247 (6.27)/.237 (6.02) dimension. Then place
4. Place front insulator over contact. Push parts into coaxia! shell. While holding parts firmly against stop
Coaxial Cable Assembly Recommendations
ARINC 404
conductor.
CA58073-0001 or CCT-408M. After crimping, crimp ring must not exceed .252 (6.40) diameter.
center contact. Crimp with Cannon tool CCT/C10.
ferrule.
dielectric flush with insulator. Then cut inner conductor to length shown.
conductor.
#WT-400 Crimp Tool while making sure parts do not move out of place.
against jacket, and comb out exposed portion of braid.
and slide rear insulator over dielectric until it presses against braid.
contact over conductor and crimp with MS3191-3 (do not use MS3191-1). Press parts firmly
against locator during crimping operation.
shoulder in coaxial shell, place jaw of crimp tool at back end of shell and crimp. Use Buchanan crimp
tool #612991 (.343 [8.71) across hex].
64
FERRULE
.400 APPROX.
(10-16)
Specifications and dimensions subject to change
COAXIAL SHELL
CRIMP AREA
JACKET
FERRULE
DPX*MA Crimp
REAR INSULATOR
JACKET
.247 (6.27)
.237 (6.02)
SHELL
Dimensions shown in inch (mm)
.198 (5.03)
CONTACT
www.ittcannon.com
.070 (1.78) MAX.
.070 (1.78)
.060 (1.52)
DIELECTRIC
.680 (17.27)
.660 (16.76)
REAR INSULATOR
CONTACT
FRONT
INSULATOR
.156 (3.96)
.136 (3.45)
.034 DIA.
(0.86)
.250 (6.35)
.230 (5.84)