ZL50110GAG Zarlink, ZL50110GAG Datasheet - Page 30

• Manufacturer Part Number: ZL50110GAG
• Description: CESoP Processor 552-Pin BGA Tray
• Manufacturer: Zarlink

Specifications of ZL50110GAG

• Package: 552BGA
• Maximum Data Rate: 1000 Mbps
• Transmission Media Type: Fiber Optic
• Power Supply Type: Analog
• Typical Supply Current: 950(Max) mA
• Typical Operating Supply Voltage: 1.8 V
• Minimum Operating Supply Voltage: 1.65 V
• Maximum Operating Supply Voltage: 1.95 V

3.1.4
Note: Speed modes:
Note: All TDM Interface inputs (including data, clock and frame pulse) have internal pull-down resistors so they can be safely left
TDM_STi[3:0]
TDM_STo[3:0]
TDM_CLKi[3:0]
TDM_CLKo[3:0]
2.048 Mbps - all 4 streams active (bits [3:0]), with 32 channels per stream - 128 total channels.
8.192 Mbps - 2 streams active (bits [1:0]), with 128 channels per stream - 256 total channels.
J2 - 2 streams active (bits [1:0]), with 98 channels per stream - 196 total channels.
unconnected if not used.
Signal
ZL50114 Variant TDM Stream Connection
I/O
OT
I D
I D
O
Table 5 - TDM Interface ZL50114 Stream Pin Definition
[3]
[2]
[1]
[0]
[3]
[2]
[1]
[0]
[3]
[2]
[1]
[0]
[3]
[2]
[1]
[0]
B4
A3
C5
B3
E9
D5
D7
F8
A2
B2
F10
D6
E7
C6
C4
F9
Package Balls
ZL50110/11/12/14
Zarlink Semiconductor Inc.
30
TDM port serial data input streams. For
different standards these pins are given
different identities:
ST-BUS: TDM_STi[3:0]
H.110:
H-MVIP: TDM_HDS[3:0]
Triggered on rising edge or falling edge
depending on standard.
only streams [1:0] are used. Streams [1:0]
are used for J2.
TDM port serial data output streams. For
different standards these pins are given
different identities:
ST-BUS: TDM_STo[3:0]
H.110:
H-MVIP: TDM_HDS[3:0]
Triggered on rising edge or falling edge
depending on standard. At 8.192 Mbps only
streams [1:0] are used. Streams [1:0] are
used for J2.
TDM port clock inputs
programmable as active high or low. Can
accept frequencies of 1.544 MHz,
2.048 MHz, 4.096 MHz, 8.192 MHz,
6.312 MHz or 16.384 MHz depending on
standard used.
streams [1:0] are used. Streams [1:0] are
used for J2.
TDM port clock outputs. Will generate
1.544 MHz, 2.048 MHz, 4.096 MHz,
6.312 MHz, 8.192 MHz or 16.384 MHz
depending on standard used. At 8.192 Mbps
only streams [1:0] are used. Streams [1:0]
are used for J2.
TDM_D[3:0]
TDM_D[3:0]
Description
At 8.192 Mbps only
At 8.192 Mbps
Data Sheet