AT32UC3A364 Atmel Corporation, AT32UC3A364 Datasheet - Page 49

• Manufacturer Part Number: AT32UC3A364
• Manufacturer: Atmel Corporation

Specifications of AT32UC3A364

• Flash (kbytes): 64 Kbytes
• Pin Count: 144
• Max. Operating Frequency: 66 MHz
• Cpu: 32-bit AVR
• # Of Touch Channels: 32
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 110
• Ext Interrupts: 110
• Usb Transceiver: 1
• Usb Speed: Hi-Speed
• Usb Interface: Device + OTG
• Spi: 6
• Twi (i2c): 2
• Uart: 4
• Lin: 4
• Ssc: 1
• Sd / Emmc: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 384
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 16
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 128
• Self Program Memory: YES
• External Bus Interface: 1
• Dram Memory: sdram
• Nand Interface: Yes
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 3.0 to 3.6
• Operating Voltage (vcc): 3.0 to 3.6
• Fpu: No
• Mpu / Mmu: Yes / No
• Timers: 6
• Output Compare Channels: 18
• Input Capture Channels: 12
• Pwm Channels: 12
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

Table 7-1.
7.5.7.3
7.5.7.4
7.5.8
32072G–11/2011
Index
0
1
2
3
4
5
Generic Clocks
Sleep Mode
Idle
Frozen
Standby
Stop
DeepStop
Static
Wake Up
Precautions when entering sleep mode
Sleep Modes
The power level of the internal voltage regulator is also adjusted according to the sleep mode to
reduce the internal regulator power consumption.
Modules communicating with external circuits should normally be disabled before entering a
sleep mode that will stop the module operation. This prevents erratic behavior when entering or
exiting sleep mode. Please refer to the relevant module documentation for recommended
actions.
Communication between the synchronous clock domains is disturbed when entering and exiting
sleep modes. This means that bus transactions are not allowed between clock domains affected
by the sleep mode. The system may hang if the bus clocks are stopped in the middle of a bus
transaction.
The CPU is automatically stopped in a safe state to ensure that all CPU bus operations are com-
plete when the sleep mode goes into effect. Thus, when entering Idle mode, no further action is
necessary.
When entering a sleep mode (except Idle mode), all HSB masters must be stopped before
entering the sleep mode. Also, if there is a chance that any PB write operations are incomplete,
the CPU should perform a read operation from any register on the PB bus before executing the
sleep instruction. This will stall the CPU while waiting for any pending PB operations to
complete.
When entering a sleep mode deeper or equal to DeepStop, the VBus asynchronous interrupt
should be disabled (USBCON.VBUSTE = 0).
The USB can be used to wake up the part from sleep modes through register AWEN of the
Power Manager.
Timers, communication modules, and other modules connected to external circuitry may require
specific clock frequencies to operate correctly. The Power Manager contains an implementation
defined number of generic clocks that can provide a wide range of accurate clock frequencies.
CPU
Stop
Stop
Stop
Stop
Stop
Stop
HSB
Run
Stop
Stop
Stop
Stop
Stop
PBA,B
GCLK
Run
Run
Stop
Stop
Stop
Stop
Osc0,1
PLL0,1,
SYSTIMER
Run
Run
Run
Stop
Stop
Stop
Osc32
Run
Run
Run
Run
Run
Stop
RCSYS
Run
Run
Run
Run
Run
Stop
BOD &
BOD33 &
Bandgap
On
On
On
On
Off
Off
Voltage
Regulator
Full power
Full power
Full power
Low power
Low power
Low power
49