ATmega64A Atmel Corporation, ATmega64A Datasheet - Page 247

• Manufacturer Part Number: ATmega64A
• Manufacturer: Atmel Corporation

Specifications of ATmega64A

• Flash (kbytes): 64 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 53
• Ext Interrupts: 8
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Twi (i2c): 1
• Uart: 2
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 4
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 4
• Output Compare Channels: 8
• Input Capture Channels: 2
• Pwm Channels: 7
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

23.9
23.9.1
8160C–AVR–07/09
Register Description
ADMUX – ADC Multiplexer Selection Register
Table 23-2.
Example:
ADMUX = 0xED (ADC3 - ADC2, 10x gain, 2.56V reference, left adjusted result).
Voltage on ADC3 is 300 mV, voltage on ADC2 is 500 mV.
ADCR = 512 * 10 * (300 - 500) / 2560 = -400 = 0x270.
ADCL will thus read 0x00, and ADCH will read 0x9C. Writing zero to ADLAR right adjusts the
result: ADCL = 0x70, ADCH = 0x02.
• Bit 7:6 – REFS1:0: Reference Selection Bits
These bits select the voltage reference for the ADC, as shown in
changed during a conversion, the change will not go in effect until this conversion is complete
(ADIF in ADCSRA is set). The internal voltage reference options may not be used if an external
reference voltage is being applied to the AREF pin.
Table 23-3.
Bit
0x07 (0x27)
Read/Write
Initial Value
V
V
V
:.
V
V
V
:.
V
V
V
REFS1
ADCn
ADCm
ADCm
ADCm
ADCm
ADCm
ADCm
ADCm
ADCm
0
0
1
1
+ 511/512 V
+ 510/512 V
+ 1/512 V
- 1/512 V
- 511/512V
- V
+ V
REF
REF
REFS0
/GAIN
/GAIN
REFS1
Correlation Between Input Voltage and Output Codes
Voltage Reference Selections for ADC
R/W
0
1
0
1
REF
REF
7
0
REF
REF
REF
/GAIN
/GAIN
/GAIN
/GAIN
/GAIN
Voltage Reference Selection
AREF, Internal Vref turned off.
AVCC with external capacitor at AREF pin.
Reserved
Internal 2.56V Voltage Reference with external capacitor at AREF pin.
REFS0
R/W
6
0
ADLAR
R/W
5
0
Read Code
0x1FF
0x1FF
0x1FE
:.
0x001
0x000
0x3FF
:.
0x201
0x200
MUX4
R/W
4
0
MUX3
R/W
3
0
MUX2
Corresponding Decimal Value
R/W
2
0
Table
MUX1
R/W
1
0
ATmega64A
-511
-512
511
511
510
23-3. If these bits are
-1
:.
1
0
:.
MUX0
R/W
0
0
ADMUX
247