ATxmega192A3 Atmel Corporation, ATxmega192A3 Datasheet - Page 233

• Manufacturer Part Number: ATxmega192A3
• Manufacturer: Atmel Corporation

Specifications of ATxmega192A3

• Flash (kbytes): 192 Kbytes
• Pin Count: 64
• Max. Operating Frequency: 32 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 50
• Ext Interrupts: 50
• Usb Speed: No
• Usb Interface: No
• Spi: 10
• Twi (i2c): 2
• Uart: 7
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 16
• Adc Resolution (bits): 12
• Adc Speed (ksps): 2000
• Analog Comparators: 4
• Resistive Touch Screen: No
• Dac Channels: 2
• Dac Resolution (bits): 12
• Temp. Sensor: Yes
• Crypto Engine: AES/DES
• Sram (kbytes): 16
• Eeprom (bytes): 2048
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: Yes
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 1.6 to 3.6
• Operating Voltage (vcc): 1.6 to 3.6
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 7
• Output Compare Channels: 22
• Input Capture Channels: 22
• Pwm Channels: 22
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

20.7.2
20.7.3
8077H–AVR–12/09
INTCTRL - SPI Interrupt Control Register
STATUS - SPI Status Register
• Bits 1:0 - PRESCALER[1:0]: SPI Clock Prescaler
These two bits control the SCK rate of the device configured in a Master mode. These bits have
no effect in Slave mode. The relationship between SCK and the Peripheral Clock frequency (clk-
PER
Table 20-4.
• Bits 7:2 - Reserved
These bits are unused and reserved for future use. For compatibility with future devices, always
write these bits to zero when this register is written.
• Bits 1:0 - INTLVL[1:0]: SPI Interrupt Level
These bits enable the SPI Interrupt and select the interrupt level as described in
”Interrupts and Programmable Multi-level Interrupt Controller” on page
rupt will be triggered when the IF in the STATUS register is set.
• Bit 7 - IF: SPI Interrupt Flag
When a serial transfer is complete and one byte is completely shifted in/out of the DATA regis-
ter, the IF bit is set. If SS is an input and is driven low when the SPI is in Master mode, this will
also set the IF bit. The IF is cleared by hardware when executing the corresponding interrupt
handling vector. Alternatively, the SPIF bit can be cleared by first reading the STATUS register
with IF set, and then access the DATA register.
Bit
+0x01
Read/Write
Initial Value
Bit
+0x02
Read/Write
Initial Value
)is shown in
CLK2X
0
0
0
0
1
1
1
1
SPIF
7
R
0
R
-
7
0
Relationship Between SCK and the Peripheral Clock (clk
Table 20-4 on page
WCOL
6
R
0
R
6
0
-
PRESCALER[1:0]
R
R
5
0
5
0
-
-
00
01
10
11
00
01
10
11
233.
R
R
4
0
4
0
-
-
R
R
3
0
3
0
SCK Frequency
clk
clk
clk
clk
clk
clk
clk
clk
-
-
PER
PER
PER
PER
PER
PER
PER
PER
/4
/16
/64
/128
/2
/8
/32
/64
R
R
2
0
2
0
-
-
R/W
PER
R
1
0
1
0
-
123. The enabled inter-
INTLVL[1:0]
) frequency
XMEGA A
R/W
R/W
0
0
0
0
-
Section 12.
INTCTRL
STATUS
233