AD5663R Analog Devices, AD5663R Datasheet - Page 20

• Manufacturer Part Number: AD5663R
• Manufacturer: Analog Devices

Specifications of AD5663R

• Resolution (bits): 16bit
• Dac Update Rate: 220kSPS
• Dac Settling Time: 4µs
• Max Pos Supply (v): +5.5V
• Single-supply: Yes
• Dac Type: Voltage Out
• Dac Input Format: Ser,SPI

AD5623R/AD5643R/AD5663R
THEORY OF OPERATION
DIGITAL-TO-ANALOG SECTION
The AD5623R/AD5643R/AD5663R DAC is fabricated on
a CMOS process. The architecture consists of a string DAC
followed by an output buffer amplifier. Figure 49 shows a block
diagram of the DAC architecture.
Because the input coding to the DAC is straight binary, the ideal
output voltage when using an external reference is given by
The ideal output voltage when using the internal reference is
given by
where:
D is the decimal equivalent of the binary code that is loaded to
the DAC register:
N is the DAC resolution.
RESISTOR STRING
The resistor string section is shown in Figure 50. It is simply a
string of resistors, each of Value R. The code loaded to the DAC
register determines at which node on the string the voltage is
tapped off to be fed into the output amplifier. The voltage is
tapped off by closing one of the switches connecting the string
to the amplifier. Because it is a string of resistors, it is guaranteed
monotonic.
OUTPUT AMPLIFIER
The output buffer amplifier can generate rail-to-rail voltages on
its output, which gives an output range of 0 V to V
a load of 2 kΩ in parallel with 1000 pF to GND. The source and
sink capabilities of the output amplifier can be seen in Figure 31.
The slew rate is 1.8 V/μs with a 1/4 to 3/4 full-scale settling time
of 10 μs.
0 to 4095 for AD5623R (12-bit)
0 to 16,383 for AD5643R (14-bit)
0 to 65,535 for AD5663R (16-bit)
REGISTER
DAC
V
OUT
Figure 49. DAC Architecture
V
OUT
=
RESISTOR
2
=
STRING
REF (+)
REF (–)
×
GND
V
V
V
DD
REFIN
REFOUT
×
⎛
⎜
⎝
×
2
D
⎛
⎜
⎝
N
2
D
OUTPUT
AMPLIFIER
(GAIN = +2)
⎞
⎟
⎠
N
⎞
⎟
⎠
DD
V
OUT
. It can drive
Rev. D | Page 20 of 32
INTERNAL REFERENCE
The AD5623R/AD5643R/AD5663R on-chip reference is off at
power-up and is enabled via a write to a control register. See the
Internal Reference Setup section for details.
The AD56x3R-3 has a 1.25 V, 5 ppm/°C reference, giving a full-
scale output of 2.5 V. The AD56x3R-5 has a 2.5 V, 5 ppm/°C
reference, giving a full-scale output of 5 V. The internal refer-
ence associated with each part is available at the V
A buffer is required if the reference output is used to drive
external loads. When using the internal reference, it is
recommended that a 100 nF capacitor be placed between
reference output and GND for reference stability.
EXTERNAL REFERENCE
The V
the use of an external reference if the application requires it.
The on-chip reference is off at power-up, and this is the default
condition. The AD56x3R-3 and the AD56x3R-5 can be operated
from a single 2.7 V to 5.5 V supply.
SERIAL INTERFACE
The AD5623R/AD5643R/AD5663R have a 3-wire serial interface
( SYNC , SCLK, and DIN) that is compatible with SPI, QSPI, and
MICROWIRE interface standards, as well as with most DSPs.
See
The write sequence begins by bringing the SYNC line low. Data
from the DIN line is clocked into the 24-bit shift register on the
falling edge of SCLK. The serial clock frequency can be as high
as 50 MHz, making the AD5623R/AD5643R/AD5663R compatible
with high speed DSPs. On the 24th falling clock edge, the last
data bit is clocked in and the programmed function is executed,
for example, a change in DAC register contents and/or a change
in the mode of operation.
Figure 2
REFIN
pins on the AD56x3R-3 and the AD56x3R-5 allows
for a timing diagram of a typical write sequence.
R
R
R
R
R
Figure 50. Resistor String
TO OUTPUT
AMPLIFIER
REFOUT
pin.