BTS 50055-1TMC Infineon Technologies, BTS 50055-1TMC Datasheet
BTS 50055-1TMC
Specifications of BTS 50055-1TMC
Related parts for BTS 50055-1TMC
BTS 50055-1TMC Summary of contents
Page 1
... Logic GND 1 ) With additional external diode Additional external diode required for energized inductive loads (see page 8). Infineon Technologies AG Product Summary Operating voltage On-state resistance Noinal current Load current (ISO) Short circuit current limitation I Current sense ratio 1 ) chip on chip technology. Providing embedded protective functions. ...
Page 2
Pin Symbol 1 OUT O 2 OUT OUT O 7 OUT O Maximum Ratings °C unless otherwise specified j Parameter Supply voltage (overvoltage protection ...
Page 3
Thermal Characteristics Parameter and Conditions Thermal resistance junction - ambient (free air): R SMD version, device on PCB Electrical Characteristics Parameter and Conditions -40 ... +150 ° unless otherwise specified j bb Load ...
Page 4
Parameter and Conditions -40 ... +150 ° unless otherwise specified j bb Inverse Load Current Operation On-state resistance (Pins 1,2,6,7 to pin bIN ...
Page 5
Parameter and Conditions -40 ... +150 ° unless otherwise specified j bb 16) Protection Functions Short circuit current limit (Tab to pins 1,2,6, Output clamp (inductive ...
Page 6
Parameter and Conditions -40 ... +150 ° unless otherwise specified j bb Sense current saturation Current sense leakage current Current sense overvoltage protection Current sense settling time Input ...
Page 7
Terms 4 V bIN PROFET bIS Two or more devices can easily be connected in parallel to increase load current capability. Input circuit ...
Page 8
... To minimize power dissipation at reverse battery operation, the summarized current into the IN and IS pin should be about 120mA. The current can be provided by using a small signal diode D in parallel to the input switch, by using a MOSFET input switch or by proper adjusting the current through R Infineon Technologies load bb ...
Page 9
... R L > 0 Ω: · OUT(CL · L Infineon Technologies AG Maximum allowable load inductance for a single switch off j,start = 150° Ω L [µ OUT V + OUT 0). IS Externally adjustable current limit ...
Page 10
... OUT 0 V only if forced externally). So the device remains latched unless V between turn on and t . d(SC) ) Can be "switched off" by using a diode D 26 Infineon Technologies AG BTS50055-1TMC ) X < V after shutdown. In most cases V ON(SC) (see page 8) or leaving open the current sense output. S Page Data Sheet BTS50055-1TMC ...
Page 11
... ILIS ilis 30000 28000 26000 24000 22000 20000 max 18000 16000 typ 14000 12000 min 10000 Infineon Technologies AG Current sense ratio f 22000 20000 18000 16000 14000 12000 10000 ILIS I [A] L Current sense ratio f(I ILIS ...
Page 12
... ON(FB) Typ. on-state resistance [mOhm -40° Infineon Technologies AG Typ. input current [mA] IN 1.6 1.4 1.2 1.0 0.8 0.6 0 150° static dynamic = 150°C 85°C 25° ...
Page 13
... Figure 2b: Switching motors and lamps OUT Sense current saturation can occur at very high inrush currents (see I on page 6). IS,lim Infineon Technologies AG Figure 2c: Switching an inductive load dV/dtoff V OUT t off I t slc(IS ...
Page 14
... Reset if T < Auto Restart V OUT T j Figure 6f: Undervoltage restart of charge pump, overvoltage clamp V OUT V IN dynamic, short 6 Undervoltage not below V bIN( bIN(u) bIN(ucp) Infineon Technologies ON(CL ON(CL) Page Data Sheet BTS50055-1TMC 2010-April-27 ...
Page 15
... Green Product (RoHS compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant (i.e Pb- free finish on leads and suitable for Pb-free soldering according to IPC/JEDEC J-STD-020). Infineon Technologies AG BTS50055-1TMC 4.4 1.27 ± ...
Page 16
... Date Changes Rev. 1.1 2010-04-27 Limits of parameter t Limits of parameter t Rev. 1.0 2008-01-24 Initial version of data sheet. Green (RoHS compliant) variant of BTS6510B Infineon Technologies AG Data Sheet BTS50055-1TMC changed to min 130µs / max 450µs on changed to min 90µs / max 210µs off Page 2010-April-27 ...
Page 17
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...