BTS410E2E3043 Infineon Technologies AG, BTS410E2E3043 Datasheet
BTS410E2E3043
Related parts for BTS410E2E3043
BTS410E2E3043 Summary of contents
Page 1
Smart Highside Power Switch Features Overload protection Current limitation Short circuit protection Thermal shutdown Overvoltage protection (including load dump) Fast demagnetization of inductive loads 1 ) Reverse battery protection Undervoltage and overvoltage shutdown with auto-restart and hysteresis Open drain diagnostic ...
Page 2
Pin Symbol 1 GND - OUT O (Load, L) Maximum Ratings °C unless otherwise specified j Parameter Supply voltage (overvoltage protection see page 3) ) ...
Page 3
Electrical Characteristics Parameter and Conditions ° unless otherwise specified j bb Load Switching Capabilities and Characteristics On-state resistance (pin 1 Nominal load current, ISO Norm ...
Page 4
Parameter and Conditions ° unless otherwise specified j bb Protection Functions 9) Initial peak short circuit current limit (pin max 450 > ON(SC) ...
Page 5
Parameter and Conditions ° unless otherwise specified j bb Input and Status Feedback Input turn-on threshold voltage Input turn-off threshold voltage Input threshold hysteresis Off state input current (pin 2 ...
Page 6
Truth Table Input- Output level level Normal L L operation H H Open load Short circuit GND H L Short circuit Overtem perature ...
Page 7
Status output R ST(ON) GND ESD-Zener diode typ., max 5 mA; R < 250 at 1.6 mA, ESD zener diodes are not ST(ON used as voltage clamp at DC conditions. Operation in this mode may result ...
Page 8
GND disconnect with GND pull PROFET ST 4 GND GND bb Any kind of load device stays off GND > IN IN(T+) ...
Page 9
Typ. transient thermal impedance chip case Z = f(t , D), D=t /T thJC [K/W] thJC 10 1 0.1 0.01 1E-5 1E-4 1E-3 1E-2 Semiconductor Group D= 0.5 0.2 0.1 0.05 0.02 0.01 0 1E-1 1E0 1E1 ...
Page 10
Options Overview all versions: High-side switch, Input protection, ESD protection, load dump and reverse battery protection with 150 ground Type Logic version Overtemperature protection with hysteresis T j >150 °C, latch function >150 °C, ...
Page 11
Timing diagrams Figure 1a: V turn on d(bb IN OUT A ST open drain A in case of too early V IN =high the device may not turn on (curve A) t approx. 150 ...
Page 12
Figure 3b: Turn on into overload L(SCp) I L(SCr) ST Heating up may require several seconds < 8.5 V typ. bb OUT Figure 3c: Short circuit while on OUT I ...
Page 13
Figure 5b: Open load: detection in ON-state, open load occurs in on-state IN t d(ST OL1 OUT normal open tbd s typ tbd s typ d(ST OL1) d(ST OL2) Figure 6a: Undervoltage: ...
Page 14
Figure 9a: Overvoltage at short circuit shutdown bb(o rst) Output short to GND V OUT short circuit shutdown Overvoltage due to power line inductance. No overvoltage auto- restart of PROFET after short circuit ...
Page 15
Package and Ordering Code All dimensions in mm Standard TO-220AB/5 BTS 410 E2 Q67060-S6102-A2 TO-220AB/5, Option E3043 BTS 410 E2 E3043 Q67060-S6102-A3 Semiconductor Group SMD TO-220AB/5, Opt. E3062 Ordering code BTS410E2 E3062A T&R: Changed since 04.96 Date Change Mar. E ...
Page 16
... Published by Infineon Technologies AG, St.-Martin-Strasse 53, D-81669 München © Infineon Technologies AG 2001 All Rights Reserved. Attention please! The information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. Terms of delivery and rights to technical change reserved. We hereby disclaim any and all warranties, including but not limited to warranties of non-infringement, regarding circuits, descriptions and charts stated herein ...