SW06 Analog Devices, Inc., SW06 Datasheet
SW06
Available stocks
Related parts for SW06
SW06 Summary of contents
Page 1
... With V– the analog signal range will extend from ground to +32 V. PNP logic inputs are TTL and CMOS compatible to allow the SW06 to upgrade existing designs. The logic “0” and logic “1” input currents are at microampere levels reducing loading on CMOS and TTL logic. ...
Page 2
... All Channels “OFF”, 3 DIS = “0” All Channels “OFF”, 3 DIS = “0” All Channels “ON” “OFF” –2– = +25 C, unless otherwise noted) A SW06B SW06F SW06G Min Typ Max Min Typ Max 100 100 100 100 5 10 ...
Page 3
... Guaranteed by design. 9 Parameter tested only +125 C for military grade device. A Specifications subject to change without notice. REV +15 V, V– = –15 V, – SW06FQ and – +85 C for SW06GP/GS, unless otherwise noted) A Conditions Min Typ Max Operating – 1.0 mA ...
Page 4
... Limit Units 100 max max 6.0 9.0 mA max 5.0 7.0 mA max 4.0 4.0 mA max 10.0 10.0 V min 2.0 2.0 V min 0.8 0.8 V max 5.0 5 min = +25 C, unless otherwise noted) A SW06N SW06G Typical Typical Units 340 340 ns 200 200 ns 0.3 0 max A max A max REV. A ...
Page 5
... ABSOLUTE MAXIMUM RATINGS Operating Temperature Range SW06BQ, BRC . . . . . . . . . . . . . . . . . . . – +125 C SW06FQ . . . . . . . . . . . . . . . . . . . . . . . . . – +85 C SW06GP – +85 C Storage Temperature Range . . . . . . . . . . . – +150 C Lead Temperature (Soldering, 60 sec +300 C Maximum Junction Temperature . . . . . . . . . . . . . . . . +150 C V+ Supply to V– Supply . . . . . . . . . . . . . . . . . . . . . . . + Supply to Ground . . . . . . . . . . . . . . . . . . . . . . . . . +36 V Logic Input Voltage . . . . . . . . . . . (– ...
Page 6
... SW06–Typical Performance Characteristics “ON” Resistance vs. Power Supply Voltage Switch Current vs. Voltage Supply Current vs. Temperature “ON” Resistance vs. Analog Voltage Leakage Current vs. Analog Voltage Supply Current vs. Supply Voltage –6– R vs. Temperature ON Leakage Current vs. Temperature Switch Capacitance vs. Analog Voltage REV. A ...
Page 7
... T /T Switching Response ON OFF Insertion Loss vs. Frequency Power Supply Rejection vs. Frequency REV. A Switching Time vs. Analog Voltage Crosstalk and “OFF” Isolation vs. Frequency Overvoltage Characteristics –7– SW06 Switching Time vs. Temperature Total Harmonic Distortion ...
Page 8
... SW06–Typical Performance Characteristics (Operating and Single Supply) “On” Resistance vs. Analog Voltage Switching Time vs. Supply Voltage Leakage Current vs. V ANALOG NOTE These single-supply-operation characteristic curves are valid when the negative power supply V– is tied to the logic ground reference pin “GND.” TTL input compatibility is still main- tained when “ ...
Page 9
... Isolation Test Circuit REV. A Crosstalk Test Circuit Switching Time Test Circuit –9– SW06 ...
Page 10
... APPLICATIONS INFORMATION The single analog switch product configures, by appropriate pin connections, into four switch applications. As shown in Figure 1, the SW06 connects as a QUAD SPST, a DUAL SPDT, a DUAL DPST DPDT analog switch. This versatility in- creases further when taking advantage of the disable input (DIS) which turns all switches OFF when taken active low ...
Page 11
... This product operates with power supply voltages ranging from OFF volts; however, the specifications only guarantee device parameters with 15 volt 5% power supplies. The ). power supply sensitive parameters have plots to indicate effects X of supply voltages other than 15 volts switching L –11– SW06 4-Channel Sample Hold Amplifier but ...
Page 12
... SW06 Single Pole Double Throw Selector Switch with Break-Before-Make Interval 20-Terminal Leadless Chip Carrier (RC-Suffix) E-20A 0.200 (5.08) 0.075 0.100 (2.54) (1.91) 0.064 (1.63) REF 0.095 (2.41) 19 0.075 (1.90) 18 0.358 0.358 (9.09) 0.011 (0.28) (9.09) BOTTOM 0.342 (8.69) 0.007 (0.18) MAX SQ R TYP SQ 14 0.075 (1.91) 13 REF 0.055 (1.40) 0.088 (2.24) 0.054 (1.37) 0.045 (1.14) 16-Lead Plastic DIP ...