DS1035 Dallas Semiconducotr, DS1035 Datasheet

no-image

DS1035

Manufacturer Part Number
DS1035
Description
3-in-1 High Speed Silicon Delay Line
Manufacturer
Dallas Semiconducotr
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DS1035
Manufacturer:
DALLAS
Quantity:
20 000
Part Number:
DS1035M
Manufacturer:
DALLAS
Quantity:
20 000
Part Number:
DS1035Z-10
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
DS1035Z-10/T&R
Manufacturer:
DALLAS
Quantity:
20 000
Part Number:
DS1035Z-12
Manufacturer:
MAXIM/美信
Quantity:
20 000
www.DataSheet4U.com
FEATURES
DESCRIPTION
The DS1035 series is a low-power +5-volt high-speed version of the popular DS1013 and complements
the DS1033 +3.3 Volt version.
The DS1035 series of delay lines have three independent logic buffered delays in a single package. The
device is Dallas Semiconductor’s fastest 3-in-1 delay line. It is available in a standard 8-pin DIP and 150
Mil 8-pin Mini-SOIC.
The device features precise leading and trailing edge accuracies. It has the inherent reliability of an all-
silicon delay line solution. The DS1035’s initial tolerance is 1.5 or 2.0 ns with an additional tolerance
over temperature and voltage of 1.0 ns or 1.5 ns, depending on the delay value. Each output is capable
of driving up to 10 LS loads.
Standard delay values are indicated in Table 1. Customers may contact Dallas Semiconductor at (982)
371-4348 for further information.
www.dalsemi.com
All-silicon timing circuit
Three independent buffered delays
Stable and precise over temperature and
voltage
Leading and trailing edge precision preserves
the input symmetry
Standard 8-pin DIP and 8-pin SOIC (150 mil)
Vapor phasing, IR and wave solderable
Available in Tape and Reel
3-in-1 High–Speed Silicon Delay Line
1 of 6
PIN ASSIGNMENT
PIN DESCRIPTION
IN1-IN3
OUT1-OUT3
NC
V
GND
(Sub)
CC
GND
DS1035Z 8-Pin SOIC (150-mil)
GND
IN1
IN2
IN3
See Mech. Drawings Section
See Mech. Drawings Section
IN1
IN2
IN3
DS1035M 8-Pin DIP
1
2
3
4
1
2
4
3
- Input Signals
- Output Signals
- No Connection
- +5 Volt Supply
- Ground
- Internal substrate
connection, do not make
any external connections
to these pins
8
7
5
6
5
8
7
6
V
OUT3
OUT1
OUT2
CC
V
OUT3
OUT1
OUT2
CC
DS1035
111799

Related parts for DS1035

DS1035 Summary of contents

Page 1

... The DS1035 series is a low-power +5-volt high-speed version of the popular DS1013 and complements the DS1033 +3.3 Volt version. The DS1035 series of delay lines have three independent logic buffered delays in a single package. The device is Dallas Semiconductor’s fastest 3-in-1 delay line available in a standard 8-pin DIP and 150 Mil 8-pin Mini-SOIC ...

Page 2

... DELAY PER PART NUMBER OUTPUT (ns) DS1035-60 DS1035-80 DS1035-10 DS1035-12 DS1035-15 DS1035-20 DS1035-25 DS1035-30 NOTES: 1. Nominal conditions are +25 C and V 2. Temperature range and voltage range of 4.75 volts to 5.25 volts. 3. Delay accuracy is for both leading and trailing edges Table 1 PLH PHL ...

Page 3

... The input waveform is produced by a precision pulse generator under software control. Time delays are measured by a time interval counter (20 ps resolution ) connected to the output. The DS1035 output taps are selected and connected to the interval counter by a VHF switch control unit. All measurements are fully automated with each instrument controlled by the computer over an IEEE 488 bus ...

Page 4

... OR SYMBOL MIN (0°C to 70°C; V =+5V ± 5%) CC MIN TYP MAX 4.75 5.00 5. 2.2 +0.5 -0.5 0.8 -1.0 +1.0 -1.0 12 (+25°C; V =5V ± 5%) CC TYP MAX UNITS 2.0 2.5 ns 100 ms (T TYP MAX UNITS 10 DS1035 UNITS NOTES 3 3 =25°C) A NOTES pF ...

Page 5

... All voltages are referenced to ground volts and 25 C, delay accuracy on both the rising and falling edges within tolerances given CC in Table 1. 3. Pulse width and duty cycle specifications may be exceeded; however, accuracy will be application sensitive with respect to decoupling, layout, etc DS1035 ...

Page 6

... PLH pulse and the 1.5 volt point on the leading edge of the output pulse. t (Time Delay, Falling): The elapsed time between the 1.5 volt point on the falling edge of the input PHL pulse and the 1.5 volt point on the falling edge of the output pulse DS1035 ...

Related keywords